Contributors: 16
| Author |
Tokens |
Token Proportion |
Commits |
Commit Proportion |
| Linus Walleij |
187 |
46.98% |
10 |
25.64% |
| Lee Jones |
67 |
16.83% |
7 |
17.95% |
| Arnd Bergmann |
32 |
8.04% |
4 |
10.26% |
| Fabio Baltieri |
30 |
7.54% |
1 |
2.56% |
| Srinidhi Kasagar |
24 |
6.03% |
2 |
5.13% |
| Russell King |
20 |
5.03% |
1 |
2.56% |
| Rabin Vincent |
18 |
4.52% |
4 |
10.26% |
| Rob Herring |
4 |
1.01% |
2 |
5.13% |
| Robert Marklund |
3 |
0.75% |
1 |
2.56% |
| Per Forlin |
3 |
0.75% |
1 |
2.56% |
| Catalin Marinas |
3 |
0.75% |
1 |
2.56% |
| Axel Lin |
2 |
0.50% |
1 |
2.56% |
| Thomas Gleixner |
2 |
0.50% |
1 |
2.56% |
| Shawn Guo |
1 |
0.25% |
1 |
2.56% |
| Mark Rutland |
1 |
0.25% |
1 |
2.56% |
| Linus Torvalds |
1 |
0.25% |
1 |
2.56% |
| Total |
398 |
|
39 |
|
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2008-2009 ST-Ericsson SA
*
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/mfd/dbx500-prcmu.h>
#include <linux/platform_data/arm-ux500-pm.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/regulator/machine.h>
#include <asm/outercache.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
static int __init ux500_l2x0_unlock(void)
{
int i;
struct device_node *np;
void __iomem *l2x0_base;
np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
l2x0_base = of_iomap(np, 0);
of_node_put(np);
if (!l2x0_base)
return -ENODEV;
/*
* Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
* apparently locks both caches before jumping to the kernel. The
* l2x0 core will not touch the unlock registers if the l2x0 is
* already enabled, so we do it right here instead. The PL310 has
* 8 sets of registers, one per possible CPU.
*/
for (i = 0; i < 8; i++) {
writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
i * L2X0_LOCKDOWN_STRIDE);
writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
i * L2X0_LOCKDOWN_STRIDE);
}
iounmap(l2x0_base);
return 0;
}
static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
{
/*
* We can't write to secure registers as we are in non-secure
* mode, until we have some SMI service available.
*/
}
/*
* FIXME: Should we set up the GPIO domain here?
*
* The problem is that we cannot put the interrupt resources into the platform
* device until the irqdomain has been added. Right now, we set the GIC interrupt
* domain from init_irq(), then load the gpio driver from
* core_initcall(nmk_gpio_init) and add the platform devices from
* arch_initcall(customize_machine).
*
* This feels fragile because it depends on the gpio device getting probed
* _before_ any device uses the gpio interrupts.
*/
static void __init ux500_init_irq(void)
{
struct device_node *np;
struct resource r;
irqchip_init();
prcmu_early_init();
np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
of_address_to_resource(np, 0, &r);
of_node_put(np);
if (!r.start) {
pr_err("could not find PRCMU base resource\n");
return;
}
ux500_pm_init(r.start, r.end-r.start);
/* Unlock before init */
ux500_l2x0_unlock();
outer_cache.write_sec = ux500_l2c310_write_sec;
}
static void ux500_restart(enum reboot_mode mode, const char *cmd)
{
local_irq_disable();
local_fiq_disable();
prcmu_system_reset(0);
}
static const struct of_device_id u8500_local_bus_nodes[] = {
/* only create devices below soc node */
{ .compatible = "stericsson,db8500", },
{ .compatible = "simple-bus"},
{ },
};
static void __init u8500_init_machine(void)
{
of_platform_populate(NULL, u8500_local_bus_nodes,
NULL, NULL);
}
static const char * stericsson_dt_platform_compat[] = {
"st-ericsson,u8500",
"st-ericsson,u9500",
NULL,
};
DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
.l2c_aux_val = 0,
.l2c_aux_mask = ~0,
.init_irq = ux500_init_irq,
.init_machine = u8500_init_machine,
.dt_compat = stericsson_dt_platform_compat,
.restart = ux500_restart,
MACHINE_END