Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Rahul Tanwar | 2755 | 67.76% | 1 | 5.00% |
Eliav Farber | 1292 | 31.78% | 13 | 65.00% |
Guenter Roeck | 6 | 0.15% | 1 | 5.00% |
Jeff Johnson | 5 | 0.12% | 1 | 5.00% |
Christophe Jaillet | 3 | 0.07% | 1 | 5.00% |
Daniel Lezcano | 3 | 0.07% | 1 | 5.00% |
Arseny Demidov | 1 | 0.02% | 1 | 5.00% |
Uwe Kleine-König | 1 | 0.02% | 1 | 5.00% |
Total | 4066 | 20 |
// SPDX-License-Identifier: GPL-2.0 /* * Copyright (C) 2020 MaxLinear, Inc. * * This driver is a hardware monitoring driver for PVT controller * (MR75203) which is used to configure & control Moortec embedded * analog IP to enable multiple embedded temperature sensor(TS), * voltage monitor(VM) & process detector(PD) modules. */ #include <linux/bits.h> #include <linux/clk.h> #include <linux/debugfs.h> #include <linux/hwmon.h> #include <linux/kstrtox.h> #include <linux/module.h> #include <linux/mod_devicetable.h> #include <linux/mutex.h> #include <linux/platform_device.h> #include <linux/property.h> #include <linux/regmap.h> #include <linux/reset.h> #include <linux/slab.h> #include <linux/units.h> /* PVT Common register */ #define PVT_IP_CONFIG 0x04 #define TS_NUM_MSK GENMASK(4, 0) #define TS_NUM_SFT 0 #define PD_NUM_MSK GENMASK(12, 8) #define PD_NUM_SFT 8 #define VM_NUM_MSK GENMASK(20, 16) #define VM_NUM_SFT 16 #define CH_NUM_MSK GENMASK(31, 24) #define CH_NUM_SFT 24 #define VM_NUM_MAX (VM_NUM_MSK >> VM_NUM_SFT) /* Macro Common Register */ #define CLK_SYNTH 0x00 #define CLK_SYNTH_LO_SFT 0 #define CLK_SYNTH_HI_SFT 8 #define CLK_SYNTH_HOLD_SFT 16 #define CLK_SYNTH_EN BIT(24) #define CLK_SYS_CYCLES_MAX 514 #define CLK_SYS_CYCLES_MIN 2 #define SDIF_DISABLE 0x04 #define SDIF_STAT 0x08 #define SDIF_BUSY BIT(0) #define SDIF_LOCK BIT(1) #define SDIF_W 0x0c #define SDIF_PROG BIT(31) #define SDIF_WRN_W BIT(27) #define SDIF_WRN_R 0x00 #define SDIF_ADDR_SFT 24 #define SDIF_HALT 0x10 #define SDIF_CTRL 0x14 #define SDIF_SMPL_CTRL 0x20 /* TS & PD Individual Macro Register */ #define COM_REG_SIZE 0x40 #define SDIF_DONE(n) (COM_REG_SIZE + 0x14 + 0x40 * (n)) #define SDIF_SMPL_DONE BIT(0) #define SDIF_DATA(n) (COM_REG_SIZE + 0x18 + 0x40 * (n)) #define SAMPLE_DATA_MSK GENMASK(15, 0) #define HILO_RESET(n) (COM_REG_SIZE + 0x2c + 0x40 * (n)) /* VM Individual Macro Register */ #define VM_COM_REG_SIZE 0x200 #define VM_SDIF_DONE(vm) (VM_COM_REG_SIZE + 0x34 + 0x200 * (vm)) #define VM_SDIF_DATA(vm, ch) \ (VM_COM_REG_SIZE + 0x40 + 0x200 * (vm) + 0x4 * (ch)) /* SDA Slave Register */ #define IP_CTRL 0x00 #define IP_RST_REL BIT(1) #define IP_RUN_CONT BIT(3) #define IP_AUTO BIT(8) #define IP_VM_MODE BIT(10) #define IP_CFG 0x01 #define CFG0_MODE_2 BIT(0) #define CFG0_PARALLEL_OUT 0 #define CFG0_12_BIT 0 #define CFG1_VOL_MEAS_MODE 0 #define CFG1_PARALLEL_OUT 0 #define CFG1_14_BIT 0 #define IP_DATA 0x03 #define IP_POLL 0x04 #define VM_CH_INIT BIT(20) #define VM_CH_REQ BIT(21) #define IP_TMR 0x05 #define POWER_DELAY_CYCLE_256 0x100 #define POWER_DELAY_CYCLE_64 0x40 #define PVT_POLL_DELAY_US 20 #define PVT_POLL_TIMEOUT_US 20000 #define PVT_CONV_BITS 10 #define PVT_N_CONST 90 #define PVT_R_CONST 245805 #define PVT_TEMP_MIN_mC -40000 #define PVT_TEMP_MAX_mC 125000 /* Temperature coefficients for series 5 */ #define PVT_SERIES5_H_CONST 200000 #define PVT_SERIES5_G_CONST 60000 #define PVT_SERIES5_J_CONST -100 #define PVT_SERIES5_CAL5_CONST 4094 /* Temperature coefficients for series 6 */ #define PVT_SERIES6_H_CONST 249400 #define PVT_SERIES6_G_CONST 57400 #define PVT_SERIES6_J_CONST 0 #define PVT_SERIES6_CAL5_CONST 4096 #define TEMPERATURE_SENSOR_SERIES_5 5 #define TEMPERATURE_SENSOR_SERIES_6 6 #define PRE_SCALER_X1 1 #define PRE_SCALER_X2 2 /** * struct voltage_device - VM single input parameters. * @vm_map: Map channel number to VM index. * @ch_map: Map channel number to channel index. * @pre_scaler: Pre scaler value (1 or 2) used to normalize the voltage output * result. * * The structure provides mapping between channel-number (0..N-1) to VM-index * (0..num_vm-1) and channel-index (0..ch_num-1) where N = num_vm * ch_num. * It also provides normalization factor for the VM equation. */ struct voltage_device { u32 vm_map; u32 ch_map; u32 pre_scaler; }; /** * struct voltage_channels - VM channel count. * @total: Total number of channels in all VMs. * @max: Maximum number of channels among all VMs. * * The structure provides channel count information across all VMs. */ struct voltage_channels { u32 total; u8 max; }; struct temp_coeff { u32 h; u32 g; u32 cal5; s32 j; }; struct pvt_device { struct regmap *c_map; struct regmap *t_map; struct regmap *p_map; struct regmap *v_map; struct clk *clk; struct reset_control *rst; struct dentry *dbgfs_dir; struct voltage_device *vd; struct voltage_channels vm_channels; struct temp_coeff ts_coeff; u32 t_num; u32 p_num; u32 v_num; u32 ip_freq; }; static ssize_t pvt_ts_coeff_j_read(struct file *file, char __user *user_buf, size_t count, loff_t *ppos) { struct pvt_device *pvt = file->private_data; unsigned int len; char buf[13]; len = scnprintf(buf, sizeof(buf), "%d\n", pvt->ts_coeff.j); return simple_read_from_buffer(user_buf, count, ppos, buf, len); } static ssize_t pvt_ts_coeff_j_write(struct file *file, const char __user *user_buf, size_t count, loff_t *ppos) { struct pvt_device *pvt = file->private_data; int ret; ret = kstrtos32_from_user(user_buf, count, 0, &pvt->ts_coeff.j); if (ret) return ret; return count; } static const struct file_operations pvt_ts_coeff_j_fops = { .read = pvt_ts_coeff_j_read, .write = pvt_ts_coeff_j_write, .open = simple_open, .owner = THIS_MODULE, .llseek = default_llseek, }; static void devm_pvt_ts_dbgfs_remove(void *data) { struct pvt_device *pvt = (struct pvt_device *)data; debugfs_remove_recursive(pvt->dbgfs_dir); pvt->dbgfs_dir = NULL; } static int pvt_ts_dbgfs_create(struct pvt_device *pvt, struct device *dev) { pvt->dbgfs_dir = debugfs_create_dir(dev_name(dev), NULL); debugfs_create_u32("ts_coeff_h", 0644, pvt->dbgfs_dir, &pvt->ts_coeff.h); debugfs_create_u32("ts_coeff_g", 0644, pvt->dbgfs_dir, &pvt->ts_coeff.g); debugfs_create_u32("ts_coeff_cal5", 0644, pvt->dbgfs_dir, &pvt->ts_coeff.cal5); debugfs_create_file("ts_coeff_j", 0644, pvt->dbgfs_dir, pvt, &pvt_ts_coeff_j_fops); return devm_add_action_or_reset(dev, devm_pvt_ts_dbgfs_remove, pvt); } static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type, u32 attr, int channel) { switch (type) { case hwmon_temp: if (attr == hwmon_temp_input) return 0444; break; case hwmon_in: if (attr == hwmon_in_input) return 0444; break; default: break; } return 0; } static long pvt_calc_temp(struct pvt_device *pvt, u32 nbs) { /* * Convert the register value to degrees centigrade temperature: * T = G + H * (n / cal5 - 0.5) + J * F */ struct temp_coeff *ts_coeff = &pvt->ts_coeff; s64 tmp = ts_coeff->g + div_s64(ts_coeff->h * (s64)nbs, ts_coeff->cal5) - ts_coeff->h / 2 + div_s64(ts_coeff->j * (s64)pvt->ip_freq, HZ_PER_MHZ); return clamp_val(tmp, PVT_TEMP_MIN_mC, PVT_TEMP_MAX_mC); } static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val) { struct pvt_device *pvt = dev_get_drvdata(dev); struct regmap *t_map = pvt->t_map; u32 stat, nbs; int ret; switch (attr) { case hwmon_temp_input: ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel), stat, stat & SDIF_SMPL_DONE, PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; ret = regmap_read(t_map, SDIF_DATA(channel), &nbs); if (ret < 0) return ret; nbs &= SAMPLE_DATA_MSK; /* * Convert the register value to * degrees centigrade temperature */ *val = pvt_calc_temp(pvt, nbs); return 0; default: return -EOPNOTSUPP; } } static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val) { struct pvt_device *pvt = dev_get_drvdata(dev); struct regmap *v_map = pvt->v_map; u32 n, stat, pre_scaler; u8 vm_idx, ch_idx; int ret; if (channel >= pvt->vm_channels.total) return -EINVAL; vm_idx = pvt->vd[channel].vm_map; ch_idx = pvt->vd[channel].ch_map; switch (attr) { case hwmon_in_input: ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx), stat, stat & SDIF_SMPL_DONE, PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx, ch_idx), &n); if (ret < 0) return ret; n &= SAMPLE_DATA_MSK; pre_scaler = pvt->vd[channel].pre_scaler; /* * Convert the N bitstream count into voltage. * To support negative voltage calculation for 64bit machines * n must be cast to long, since n and *val differ both in * signedness and in size. * Division is used instead of right shift, because for signed * numbers, the sign bit is used to fill the vacated bit * positions, and if the number is negative, 1 is used. * BIT(x) may not be used instead of (1 << x) because it's * unsigned. */ *val = pre_scaler * (PVT_N_CONST * (long)n - PVT_R_CONST) / (1 << PVT_CONV_BITS); return 0; default: return -EOPNOTSUPP; } } static int pvt_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long *val) { switch (type) { case hwmon_temp: return pvt_read_temp(dev, attr, channel, val); case hwmon_in: return pvt_read_in(dev, attr, channel, val); default: return -EOPNOTSUPP; } } static struct hwmon_channel_info pvt_temp = { .type = hwmon_temp, }; static struct hwmon_channel_info pvt_in = { .type = hwmon_in, }; static const struct hwmon_ops pvt_hwmon_ops = { .is_visible = pvt_is_visible, .read = pvt_read, }; static struct hwmon_chip_info pvt_chip_info = { .ops = &pvt_hwmon_ops, }; static int pvt_init(struct pvt_device *pvt) { u16 sys_freq, key, middle, low = 4, high = 8; struct regmap *t_map = pvt->t_map; struct regmap *p_map = pvt->p_map; struct regmap *v_map = pvt->v_map; u32 t_num = pvt->t_num; u32 p_num = pvt->p_num; u32 v_num = pvt->v_num; u32 clk_synth, val; int ret; sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ; while (high >= low) { middle = (low + high + 1) / 2; key = DIV_ROUND_CLOSEST(sys_freq, middle); if (key > CLK_SYS_CYCLES_MAX) { low = middle + 1; continue; } else if (key < CLK_SYS_CYCLES_MIN) { high = middle - 1; continue; } else { break; } } /* * The system supports 'clk_sys' to 'clk_ip' frequency ratios * from 2:1 to 512:1 */ key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2; clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT | (key >> 1) << CLK_SYNTH_HI_SFT | (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN; pvt->ip_freq = clk_get_rate(pvt->clk) / (key + 2); if (t_num) { ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0); if (ret < 0) return ret; ret = regmap_write(t_map, SDIF_HALT, 0x0); if (ret < 0) return ret; ret = regmap_write(t_map, CLK_SYNTH, clk_synth); if (ret < 0) return ret; ret = regmap_write(t_map, SDIF_DISABLE, 0x0); if (ret < 0) return ret; ret = regmap_read_poll_timeout(t_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT | IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(t_map, SDIF_W, val); if (ret < 0) return ret; ret = regmap_read_poll_timeout(t_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(t_map, SDIF_W, val); if (ret < 0) return ret; ret = regmap_read_poll_timeout(t_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_CTRL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(t_map, SDIF_W, val); if (ret < 0) return ret; } if (p_num) { ret = regmap_write(p_map, SDIF_HALT, 0x0); if (ret < 0) return ret; ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1); if (ret < 0) return ret; ret = regmap_write(p_map, CLK_SYNTH, clk_synth); if (ret < 0) return ret; } if (v_num) { ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0); if (ret < 0) return ret; ret = regmap_write(v_map, SDIF_HALT, 0x0); if (ret < 0) return ret; ret = regmap_write(v_map, CLK_SYNTH, clk_synth); if (ret < 0) return ret; ret = regmap_write(v_map, SDIF_DISABLE, 0x0); if (ret < 0) return ret; ret = regmap_read_poll_timeout(v_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = (BIT(pvt->vm_channels.max) - 1) | VM_CH_INIT | IP_POLL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(v_map, SDIF_W, val); if (ret < 0) return ret; ret = regmap_read_poll_timeout(v_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT | CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(v_map, SDIF_W, val); if (ret < 0) return ret; ret = regmap_read_poll_timeout(v_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(v_map, SDIF_W, val); if (ret < 0) return ret; ret = regmap_read_poll_timeout(v_map, SDIF_STAT, val, !(val & SDIF_BUSY), PVT_POLL_DELAY_US, PVT_POLL_TIMEOUT_US); if (ret) return ret; val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE | IP_CTRL << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; ret = regmap_write(v_map, SDIF_W, val); if (ret < 0) return ret; } return 0; } static struct regmap_config pvt_regmap_config = { .reg_bits = 32, .reg_stride = 4, .val_bits = 32, }; static int pvt_get_regmap(struct platform_device *pdev, char *reg_name, struct pvt_device *pvt) { struct device *dev = &pdev->dev; struct regmap **reg_map; void __iomem *io_base; if (!strcmp(reg_name, "common")) reg_map = &pvt->c_map; else if (!strcmp(reg_name, "ts")) reg_map = &pvt->t_map; else if (!strcmp(reg_name, "pd")) reg_map = &pvt->p_map; else if (!strcmp(reg_name, "vm")) reg_map = &pvt->v_map; else return -EINVAL; io_base = devm_platform_ioremap_resource_byname(pdev, reg_name); if (IS_ERR(io_base)) return PTR_ERR(io_base); pvt_regmap_config.name = reg_name; *reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config); if (IS_ERR(*reg_map)) { dev_err(dev, "failed to init register map\n"); return PTR_ERR(*reg_map); } return 0; } static void pvt_reset_control_assert(void *data) { struct pvt_device *pvt = data; reset_control_assert(pvt->rst); } static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt) { int ret; ret = reset_control_deassert(pvt->rst); if (ret) return ret; return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt); } static int pvt_get_active_channel(struct device *dev, struct pvt_device *pvt, u32 vm_num, u32 ch_num, u8 *vm_idx) { u8 vm_active_ch[VM_NUM_MAX]; int ret, i, j, k; ret = device_property_read_u8_array(dev, "moortec,vm-active-channels", vm_active_ch, vm_num); if (ret) { /* * Incase "moortec,vm-active-channels" property is not defined, * we assume each VM sensor has all of its channels active. */ memset(vm_active_ch, ch_num, vm_num); pvt->vm_channels.max = ch_num; pvt->vm_channels.total = ch_num * vm_num; } else { for (i = 0; i < vm_num; i++) { if (vm_active_ch[i] > ch_num) { dev_err(dev, "invalid active channels: %u\n", vm_active_ch[i]); return -EINVAL; } pvt->vm_channels.total += vm_active_ch[i]; if (vm_active_ch[i] > pvt->vm_channels.max) pvt->vm_channels.max = vm_active_ch[i]; } } /* * Map between the channel-number to VM-index and channel-index. * Example - 3 VMs, "moortec,vm_active_ch" = <5 2 4>: * vm_map = [0 0 0 0 0 1 1 2 2 2 2] * ch_map = [0 1 2 3 4 0 1 0 1 2 3] */ pvt->vd = devm_kcalloc(dev, pvt->vm_channels.total, sizeof(*pvt->vd), GFP_KERNEL); if (!pvt->vd) return -ENOMEM; k = 0; for (i = 0; i < vm_num; i++) { for (j = 0; j < vm_active_ch[i]; j++) { pvt->vd[k].vm_map = vm_idx[i]; pvt->vd[k].ch_map = j; k++; } } return 0; } static int pvt_get_pre_scaler(struct device *dev, struct pvt_device *pvt) { u8 *pre_scaler_ch_list; int i, ret, num_ch; u32 channel; /* Set default pre-scaler value to be 1. */ for (i = 0; i < pvt->vm_channels.total; i++) pvt->vd[i].pre_scaler = PRE_SCALER_X1; /* Get number of channels configured in "moortec,vm-pre-scaler-x2". */ num_ch = device_property_count_u8(dev, "moortec,vm-pre-scaler-x2"); if (num_ch <= 0) return 0; pre_scaler_ch_list = kcalloc(num_ch, sizeof(*pre_scaler_ch_list), GFP_KERNEL); if (!pre_scaler_ch_list) return -ENOMEM; /* Get list of all channels that have pre-scaler of 2. */ ret = device_property_read_u8_array(dev, "moortec,vm-pre-scaler-x2", pre_scaler_ch_list, num_ch); if (ret) goto out; for (i = 0; i < num_ch; i++) { channel = pre_scaler_ch_list[i]; pvt->vd[channel].pre_scaler = PRE_SCALER_X2; } out: kfree(pre_scaler_ch_list); return ret; } static int pvt_set_temp_coeff(struct device *dev, struct pvt_device *pvt) { struct temp_coeff *ts_coeff = &pvt->ts_coeff; u32 series; int ret; /* Incase ts-series property is not defined, use default 5. */ ret = device_property_read_u32(dev, "moortec,ts-series", &series); if (ret) series = TEMPERATURE_SENSOR_SERIES_5; switch (series) { case TEMPERATURE_SENSOR_SERIES_5: ts_coeff->h = PVT_SERIES5_H_CONST; ts_coeff->g = PVT_SERIES5_G_CONST; ts_coeff->j = PVT_SERIES5_J_CONST; ts_coeff->cal5 = PVT_SERIES5_CAL5_CONST; break; case TEMPERATURE_SENSOR_SERIES_6: ts_coeff->h = PVT_SERIES6_H_CONST; ts_coeff->g = PVT_SERIES6_G_CONST; ts_coeff->j = PVT_SERIES6_J_CONST; ts_coeff->cal5 = PVT_SERIES6_CAL5_CONST; break; default: dev_err(dev, "invalid temperature sensor series (%u)\n", series); return -EINVAL; } dev_dbg(dev, "temperature sensor series = %u\n", series); /* Override ts-coeff-h/g/j/cal5 if they are defined. */ device_property_read_u32(dev, "moortec,ts-coeff-h", &ts_coeff->h); device_property_read_u32(dev, "moortec,ts-coeff-g", &ts_coeff->g); device_property_read_u32(dev, "moortec,ts-coeff-j", &ts_coeff->j); device_property_read_u32(dev, "moortec,ts-coeff-cal5", &ts_coeff->cal5); dev_dbg(dev, "ts-coeff: h = %u, g = %u, j = %d, cal5 = %u\n", ts_coeff->h, ts_coeff->g, ts_coeff->j, ts_coeff->cal5); return 0; } static int mr75203_probe(struct platform_device *pdev) { u32 ts_num, vm_num, pd_num, ch_num, val, index, i; const struct hwmon_channel_info **pvt_info; struct device *dev = &pdev->dev; u32 *temp_config, *in_config; struct device *hwmon_dev; struct pvt_device *pvt; int ret; pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL); if (!pvt) return -ENOMEM; ret = pvt_get_regmap(pdev, "common", pvt); if (ret) return ret; pvt->clk = devm_clk_get_enabled(dev, NULL); if (IS_ERR(pvt->clk)) return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n"); pvt->rst = devm_reset_control_get_optional_exclusive(dev, NULL); if (IS_ERR(pvt->rst)) return dev_err_probe(dev, PTR_ERR(pvt->rst), "failed to get reset control\n"); if (pvt->rst) { ret = pvt_reset_control_deassert(dev, pvt); if (ret) return dev_err_probe(dev, ret, "cannot deassert reset control\n"); } ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val); if (ret < 0) return ret; ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT; pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT; vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT; ch_num = (val & CH_NUM_MSK) >> CH_NUM_SFT; pvt->t_num = ts_num; pvt->p_num = pd_num; pvt->v_num = vm_num; val = 0; if (ts_num) val++; if (vm_num) val++; if (!val) return -ENODEV; pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL); if (!pvt_info) return -ENOMEM; pvt_info[0] = HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ); index = 1; if (ts_num) { ret = pvt_get_regmap(pdev, "ts", pvt); if (ret) return ret; ret = pvt_set_temp_coeff(dev, pvt); if (ret) return ret; temp_config = devm_kcalloc(dev, ts_num + 1, sizeof(*temp_config), GFP_KERNEL); if (!temp_config) return -ENOMEM; memset32(temp_config, HWMON_T_INPUT, ts_num); pvt_temp.config = temp_config; pvt_info[index++] = &pvt_temp; pvt_ts_dbgfs_create(pvt, dev); } if (pd_num) { ret = pvt_get_regmap(pdev, "pd", pvt); if (ret) return ret; } if (vm_num) { u8 vm_idx[VM_NUM_MAX]; ret = pvt_get_regmap(pdev, "vm", pvt); if (ret) return ret; ret = device_property_read_u8_array(dev, "intel,vm-map", vm_idx, vm_num); if (ret) { /* * Incase intel,vm-map property is not defined, we * assume incremental channel numbers. */ for (i = 0; i < vm_num; i++) vm_idx[i] = i; } else { for (i = 0; i < vm_num; i++) if (vm_idx[i] >= vm_num || vm_idx[i] == 0xff) { pvt->v_num = i; vm_num = i; break; } } ret = pvt_get_active_channel(dev, pvt, vm_num, ch_num, vm_idx); if (ret) return ret; ret = pvt_get_pre_scaler(dev, pvt); if (ret) return ret; in_config = devm_kcalloc(dev, pvt->vm_channels.total + 1, sizeof(*in_config), GFP_KERNEL); if (!in_config) return -ENOMEM; memset32(in_config, HWMON_I_INPUT, pvt->vm_channels.total); in_config[pvt->vm_channels.total] = 0; pvt_in.config = in_config; pvt_info[index++] = &pvt_in; } ret = pvt_init(pvt); if (ret) { dev_err(dev, "failed to init pvt: %d\n", ret); return ret; } pvt_chip_info.info = pvt_info; hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt", pvt, &pvt_chip_info, NULL); return PTR_ERR_OR_ZERO(hwmon_dev); } static const struct of_device_id moortec_pvt_of_match[] = { { .compatible = "moortec,mr75203" }, { } }; MODULE_DEVICE_TABLE(of, moortec_pvt_of_match); static struct platform_driver moortec_pvt_driver = { .driver = { .name = "moortec-pvt", .of_match_table = moortec_pvt_of_match, }, .probe = mr75203_probe, }; module_platform_driver(moortec_pvt_driver); MODULE_DESCRIPTION("Moortec Semiconductor MR75203 PVT Controller driver"); MODULE_LICENSE("GPL v2");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1