Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Peter Yin | 765 | 100.00% | 1 | 100.00% |
Total | 765 | 1 |
// SPDX-License-Identifier: GPL-2.0-or-later /* * Driver for MPS MP5990 Hot-Swap Controller */ #include <linux/i2c.h> #include <linux/module.h> #include <linux/of_device.h> #include "pmbus.h" #define MP5990_EFUSE_CFG (0xC4) #define MP5990_VOUT_FORMAT BIT(9) struct mp5990_data { struct pmbus_driver_info info; u8 vout_mode; u8 vout_linear_exponent; }; #define to_mp5990_data(x) container_of(x, struct mp5990_data, info) static int mp5990_read_byte_data(struct i2c_client *client, int page, int reg) { const struct pmbus_driver_info *info = pmbus_get_driver_info(client); struct mp5990_data *data = to_mp5990_data(info); switch (reg) { case PMBUS_VOUT_MODE: if (data->vout_mode == linear) { /* * The VOUT format used by the chip is linear11, * not linear16. Report that VOUT is in linear mode * and return exponent value extracted while probing * the chip. */ return data->vout_linear_exponent; } /* * The datasheet does not support the VOUT command, * but the device responds with a default value of 0x17. * In the standard, 0x17 represents linear mode. * Therefore, we should report that VOUT is in direct * format when the chip is configured for it. */ return PB_VOUT_MODE_DIRECT; default: return -ENODATA; } } static int mp5990_read_word_data(struct i2c_client *client, int page, int phase, int reg) { const struct pmbus_driver_info *info = pmbus_get_driver_info(client); struct mp5990_data *data = to_mp5990_data(info); int ret; s32 mantissa; switch (reg) { case PMBUS_READ_VOUT: ret = pmbus_read_word_data(client, page, phase, reg); if (ret < 0) return ret; /* * Because the VOUT format used by the chip is linear11 and not * linear16, we disregard bits[15:11]. The exponent is reported * as part of the VOUT_MODE command. */ if (data->vout_mode == linear) { mantissa = ((s16)((ret & 0x7ff) << 5)) >> 5; ret = mantissa; } break; default: return -ENODATA; } return ret; } static struct pmbus_driver_info mp5990_info = { .pages = 1, .format[PSC_VOLTAGE_IN] = direct, .format[PSC_VOLTAGE_OUT] = direct, .format[PSC_CURRENT_OUT] = direct, .format[PSC_POWER] = direct, .format[PSC_TEMPERATURE] = direct, .m[PSC_VOLTAGE_IN] = 32, .b[PSC_VOLTAGE_IN] = 0, .R[PSC_VOLTAGE_IN] = 0, .m[PSC_VOLTAGE_OUT] = 32, .b[PSC_VOLTAGE_OUT] = 0, .R[PSC_VOLTAGE_OUT] = 0, .m[PSC_CURRENT_OUT] = 16, .b[PSC_CURRENT_OUT] = 0, .R[PSC_CURRENT_OUT] = 0, .m[PSC_POWER] = 1, .b[PSC_POWER] = 0, .R[PSC_POWER] = 0, .m[PSC_TEMPERATURE] = 1, .b[PSC_TEMPERATURE] = 0, .R[PSC_TEMPERATURE] = 0, .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_PIN | PMBUS_HAVE_TEMP | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_STATUS_TEMP, .read_byte_data = mp5990_read_byte_data, .read_word_data = mp5990_read_word_data, }; static int mp5990_probe(struct i2c_client *client) { struct pmbus_driver_info *info; struct mp5990_data *data; int ret; data = devm_kzalloc(&client->dev, sizeof(struct mp5990_data), GFP_KERNEL); if (!data) return -ENOMEM; memcpy(&data->info, &mp5990_info, sizeof(*info)); info = &data->info; /* Read Vout Config */ ret = i2c_smbus_read_word_data(client, MP5990_EFUSE_CFG); if (ret < 0) { dev_err(&client->dev, "Can't get vout mode."); return ret; } /* * EFUSE_CFG (0xC4) bit9=1 is linear mode, bit=0 is direct mode. */ if (ret & MP5990_VOUT_FORMAT) { data->vout_mode = linear; data->info.format[PSC_VOLTAGE_IN] = linear; data->info.format[PSC_VOLTAGE_OUT] = linear; data->info.format[PSC_CURRENT_OUT] = linear; data->info.format[PSC_POWER] = linear; ret = i2c_smbus_read_word_data(client, PMBUS_READ_VOUT); if (ret < 0) { dev_err(&client->dev, "Can't get vout exponent."); return ret; } data->vout_linear_exponent = (u8)((ret >> 11) & 0x1f); } else { data->vout_mode = direct; } return pmbus_do_probe(client, info); } static const struct of_device_id mp5990_of_match[] = { { .compatible = "mps,mp5990" }, {} }; static const struct i2c_device_id mp5990_id[] = { {"mp5990"}, { } }; MODULE_DEVICE_TABLE(i2c, mp5990_id); static struct i2c_driver mp5990_driver = { .driver = { .name = "mp5990", .of_match_table = mp5990_of_match, }, .probe = mp5990_probe, .id_table = mp5990_id, }; module_i2c_driver(mp5990_driver); MODULE_AUTHOR("Peter Yin <peter.yin@quantatw.com>"); MODULE_DESCRIPTION("PMBus driver for MP5990 HSC"); MODULE_LICENSE("GPL"); MODULE_IMPORT_NS(PMBUS);
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1