Contributors: 10
Author |
Tokens |
Token Proportion |
Commits |
Commit Proportion |
Kim (Woogyom) Milo |
387 |
73.43% |
7 |
26.92% |
Ansuel Smith |
100 |
18.98% |
10 |
38.46% |
Maarten Zanders |
20 |
3.80% |
1 |
3.85% |
Samu Onkalo |
10 |
1.90% |
2 |
7.69% |
Sachin Kamat |
3 |
0.57% |
1 |
3.85% |
Linus Walleij |
2 |
0.38% |
1 |
3.85% |
Thomas Gleixner |
2 |
0.38% |
1 |
3.85% |
Andrew Lunn |
1 |
0.19% |
1 |
3.85% |
Uwe Kleine-König |
1 |
0.19% |
1 |
3.85% |
Masanari Iida |
1 |
0.19% |
1 |
3.85% |
Total |
527 |
|
26 |
|
// SPDX-License-Identifier: GPL-2.0-only
/*
* TI LP8501 9 channel LED Driver
*
* Copyright (C) 2013 Texas Instruments
*
* Author: Milo(Woogyom) Kim <milo.kim@ti.com>
*/
#include <linux/delay.h>
#include <linux/firmware.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/leds.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/slab.h>
#include "leds-lp55xx-common.h"
#define LP8501_PAGES_PER_ENGINE 1
#define LP8501_MAX_LEDS 9
/* Registers */
#define LP8501_REG_ENABLE 0x00
#define LP8501_ENABLE BIT(6)
#define LP8501_REG_OP_MODE 0x01
#define LP8501_REG_PWR_CONFIG 0x05
#define LP8501_PWR_CONFIG_M 0x03
#define LP8501_REG_LED_PWM_BASE 0x16
#define LP8501_REG_LED_CURRENT_BASE 0x26
#define LP8501_REG_CONFIG 0x36
#define LP8501_PWM_PSAVE BIT(7)
#define LP8501_AUTO_INC BIT(6)
#define LP8501_PWR_SAVE BIT(5)
#define LP8501_CP_MODE_MASK 0x18
#define LP8501_CP_MODE_SHIFT 3
#define LP8501_INT_CLK BIT(0)
#define LP8501_DEFAULT_CFG (LP8501_PWM_PSAVE | LP8501_AUTO_INC | LP8501_PWR_SAVE)
#define LP8501_REG_STATUS 0x3A
#define LP8501_ENGINE_BUSY BIT(4)
#define LP8501_REG_RESET 0x3D
#define LP8501_RESET 0xFF
#define LP8501_REG_PROG_MEM 0x50
static int lp8501_post_init_device(struct lp55xx_chip *chip)
{
int ret;
u8 val = LP8501_DEFAULT_CFG;
ret = lp55xx_write(chip, LP8501_REG_ENABLE, LP8501_ENABLE);
if (ret)
return ret;
/* Chip startup time is 500 us, 1 - 2 ms gives some margin */
usleep_range(1000, 2000);
if (chip->pdata->clock_mode != LP55XX_CLOCK_EXT)
val |= LP8501_INT_CLK;
val |= (chip->pdata->charge_pump_mode << LP8501_CP_MODE_SHIFT) & LP8501_CP_MODE_MASK;
ret = lp55xx_write(chip, LP8501_REG_CONFIG, val);
if (ret)
return ret;
/* Power selection for each output */
return lp55xx_update_bits(chip, LP8501_REG_PWR_CONFIG,
LP8501_PWR_CONFIG_M, chip->pdata->pwr_sel);
}
static void lp8501_run_engine(struct lp55xx_chip *chip, bool start)
{
/* stop engine */
if (!start) {
lp55xx_stop_all_engine(chip);
lp55xx_turn_off_channels(chip);
return;
}
lp55xx_run_engine_common(chip);
}
/* Chip specific configurations */
static struct lp55xx_device_config lp8501_cfg = {
.reg_op_mode = {
.addr = LP8501_REG_OP_MODE,
},
.reg_exec = {
.addr = LP8501_REG_ENABLE,
},
.engine_busy = {
.addr = LP8501_REG_STATUS,
.mask = LP8501_ENGINE_BUSY,
},
.reset = {
.addr = LP8501_REG_RESET,
.val = LP8501_RESET,
},
.enable = {
.addr = LP8501_REG_ENABLE,
.val = LP8501_ENABLE,
},
.prog_mem_base = {
.addr = LP8501_REG_PROG_MEM,
},
.reg_led_pwm_base = {
.addr = LP8501_REG_LED_PWM_BASE,
},
.reg_led_current_base = {
.addr = LP8501_REG_LED_CURRENT_BASE,
},
.pages_per_engine = LP8501_PAGES_PER_ENGINE,
.max_channel = LP8501_MAX_LEDS,
.post_init_device = lp8501_post_init_device,
.brightness_fn = lp55xx_led_brightness,
.set_led_current = lp55xx_set_led_current,
.firmware_cb = lp55xx_firmware_loaded_cb,
.run_engine = lp8501_run_engine,
};
static const struct i2c_device_id lp8501_id[] = {
{ "lp8501", .driver_data = (kernel_ulong_t)&lp8501_cfg, },
{ }
};
MODULE_DEVICE_TABLE(i2c, lp8501_id);
static const struct of_device_id of_lp8501_leds_match[] = {
{ .compatible = "ti,lp8501", .data = &lp8501_cfg, },
{},
};
MODULE_DEVICE_TABLE(of, of_lp8501_leds_match);
static struct i2c_driver lp8501_driver = {
.driver = {
.name = "lp8501",
.of_match_table = of_lp8501_leds_match,
},
.probe = lp55xx_probe,
.remove = lp55xx_remove,
.id_table = lp8501_id,
};
module_i2c_driver(lp8501_driver);
MODULE_DESCRIPTION("Texas Instruments LP8501 LED driver");
MODULE_AUTHOR("Milo Kim");
MODULE_LICENSE("GPL");