Contributors: 12
Author Tokens Token Proportion Commits Commit Proportion
Alexandru Ardelean 45 33.58% 1 8.33%
Andrea Paterniani 23 17.16% 1 8.33%
Anton Vorontsov 12 8.96% 1 8.33%
Geert Uytterhoeven 12 8.96% 1 8.33%
Qing Zhang 12 8.96% 1 8.33%
Marcelo Schmitt 7 5.22% 1 8.33%
David Brownell 6 4.48% 1 8.33%
Baruch Siach 5 3.73% 1 8.33%
Dragos Bogdan 4 2.99% 1 8.33%
Boerge Struempfel 4 2.99% 1 8.33%
Oleksij Rempel 3 2.24% 1 8.33%
Greg Kroah-Hartman 1 0.75% 1 8.33%
Total 134 12 


/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
#ifndef _UAPI_SPI_H
#define _UAPI_SPI_H

#include <linux/const.h>

#define	SPI_CPHA		_BITUL(0)	/* clock phase */
#define	SPI_CPOL		_BITUL(1)	/* clock polarity */

#define	SPI_MODE_0		(0|0)		/* (original MicroWire) */
#define	SPI_MODE_1		(0|SPI_CPHA)
#define	SPI_MODE_2		(SPI_CPOL|0)
#define	SPI_MODE_3		(SPI_CPOL|SPI_CPHA)
#define	SPI_MODE_X_MASK		(SPI_CPOL|SPI_CPHA)

#define	SPI_CS_HIGH		_BITUL(2)	/* chipselect active high? */
#define	SPI_LSB_FIRST		_BITUL(3)	/* per-word bits-on-wire */
#define	SPI_3WIRE		_BITUL(4)	/* SI/SO signals shared */
#define	SPI_LOOP		_BITUL(5)	/* loopback mode */
#define	SPI_NO_CS		_BITUL(6)	/* 1 dev/bus, no chipselect */
#define	SPI_READY		_BITUL(7)	/* slave pulls low to pause */
#define	SPI_TX_DUAL		_BITUL(8)	/* transmit with 2 wires */
#define	SPI_TX_QUAD		_BITUL(9)	/* transmit with 4 wires */
#define	SPI_RX_DUAL		_BITUL(10)	/* receive with 2 wires */
#define	SPI_RX_QUAD		_BITUL(11)	/* receive with 4 wires */
#define	SPI_CS_WORD		_BITUL(12)	/* toggle cs after each word */
#define	SPI_TX_OCTAL		_BITUL(13)	/* transmit with 8 wires */
#define	SPI_RX_OCTAL		_BITUL(14)	/* receive with 8 wires */
#define	SPI_3WIRE_HIZ		_BITUL(15)	/* high impedance turnaround */
#define	SPI_RX_CPHA_FLIP	_BITUL(16)	/* flip CPHA on Rx only xfer */
#define SPI_MOSI_IDLE_LOW	_BITUL(17)	/* leave MOSI line low when idle */
#define SPI_MOSI_IDLE_HIGH	_BITUL(18)	/* leave MOSI line high when idle */

/*
 * All the bits defined above should be covered by SPI_MODE_USER_MASK.
 * The SPI_MODE_USER_MASK has the SPI_MODE_KERNEL_MASK counterpart in
 * 'include/linux/spi/spi.h'. The bits defined here are from bit 0 upwards
 * while in SPI_MODE_KERNEL_MASK they are from the other end downwards.
 * These bits must not overlap. A static assert check should make sure of that.
 * If adding extra bits, make sure to increase the bit index below as well.
 */
#define SPI_MODE_USER_MASK	(_BITUL(19) - 1)

#endif /* _UAPI_SPI_H */