Contributors: 8
Author Tokens Token Proportion Commits Commit Proportion
Roland McGrath 105 81.40% 5 35.71%
Linus Torvalds (pre-git) 7 5.43% 3 21.43%
Gabriel Krisman Bertazi 5 3.88% 1 7.14%
Will Drewry 5 3.88% 1 7.14%
Dmitry V. Levin 4 3.10% 1 7.14%
Thomas Gleixner 1 0.78% 1 7.14%
Geert Uytterhoeven 1 0.78% 1 7.14%
Eric W. Biedermann 1 0.78% 1 7.14%
Total 129 14 


/* SPDX-License-Identifier: GPL-2.0-only */
/*
 * Access to user system call parameters and results
 *
 * Copyright (C) 2008-2009 Red Hat, Inc.  All rights reserved.
 *
 * This file is a stub providing documentation for what functions
 * arch/ARCH/include/asm/syscall.h files need to define.  Most arch definitions
 * will be simple inlines.
 *
 * All of these functions expect to be called with no locks,
 * and only when the caller is sure that the task of interest
 * cannot return to user mode while we are looking at it.
 */

#ifndef _ASM_SYSCALL_H
#define _ASM_SYSCALL_H	1

struct task_struct;
struct pt_regs;

/**
 * syscall_get_nr - find what system call a task is executing
 * @task:	task of interest, must be blocked
 * @regs:	task_pt_regs() of @task
 *
 * If @task is executing a system call or is at system call
 * tracing about to attempt one, returns the system call number.
 * If @task is not executing a system call, i.e. it's blocked
 * inside the kernel for a fault or signal, returns -1.
 *
 * Note this returns int even on 64-bit machines.  Only 32 bits of
 * system call number can be meaningful.  If the actual arch value
 * is 64 bits, this truncates to 32 bits so 0xffffffff means -1.
 *
 * It's only valid to call this when @task is known to be blocked.
 */
int syscall_get_nr(struct task_struct *task, struct pt_regs *regs);

/**
 * syscall_rollback - roll back registers after an aborted system call
 * @task:	task of interest, must be in system call exit tracing
 * @regs:	task_pt_regs() of @task
 *
 * It's only valid to call this when @task is stopped for system
 * call exit tracing (due to %SYSCALL_WORK_SYSCALL_TRACE or
 * %SYSCALL_WORK_SYSCALL_AUDIT), after ptrace_report_syscall_entry()
 * returned nonzero to prevent the system call from taking place.
 *
 * This rolls back the register state in @regs so it's as if the
 * system call instruction was a no-op.  The registers containing
 * the system call number and arguments are as they were before the
 * system call instruction.  This may not be the same as what the
 * register state looked like at system call entry tracing.
 */
void syscall_rollback(struct task_struct *task, struct pt_regs *regs);

/**
 * syscall_get_error - check result of traced system call
 * @task:	task of interest, must be blocked
 * @regs:	task_pt_regs() of @task
 *
 * Returns 0 if the system call succeeded, or -ERRORCODE if it failed.
 *
 * It's only valid to call this when @task is stopped for tracing on exit
 * from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
 * %SYSCALL_WORK_SYSCALL_AUDIT.
 */
long syscall_get_error(struct task_struct *task, struct pt_regs *regs);

/**
 * syscall_get_return_value - get the return value of a traced system call
 * @task:	task of interest, must be blocked
 * @regs:	task_pt_regs() of @task
 *
 * Returns the return value of the successful system call.
 * This value is meaningless if syscall_get_error() returned nonzero.
 *
 * It's only valid to call this when @task is stopped for tracing on exit
 * from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
 * %SYSCALL_WORK_SYSCALL_AUDIT.
 */
long syscall_get_return_value(struct task_struct *task, struct pt_regs *regs);

/**
 * syscall_set_return_value - change the return value of a traced system call
 * @task:	task of interest, must be blocked
 * @regs:	task_pt_regs() of @task
 * @error:	negative error code, or zero to indicate success
 * @val:	user return value if @error is zero
 *
 * This changes the results of the system call that user mode will see.
 * If @error is zero, the user sees a successful system call with a
 * return value of @val.  If @error is nonzero, it's a negated errno
 * code; the user sees a failed system call with this errno code.
 *
 * It's only valid to call this when @task is stopped for tracing on exit
 * from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
 * %SYSCALL_WORK_SYSCALL_AUDIT.
 */
void syscall_set_return_value(struct task_struct *task, struct pt_regs *regs,
			      int error, long val);

/**
 * syscall_get_arguments - extract system call parameter values
 * @task:	task of interest, must be blocked
 * @regs:	task_pt_regs() of @task
 * @args:	array filled with argument values
 *
 * Fetches 6 arguments to the system call.  First argument is stored in
*  @args[0], and so on.
 *
 * It's only valid to call this when @task is stopped for tracing on
 * entry to a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
 * %SYSCALL_WORK_SYSCALL_AUDIT.
 */
void syscall_get_arguments(struct task_struct *task, struct pt_regs *regs,
			   unsigned long *args);

/**
 * syscall_get_arch - return the AUDIT_ARCH for the current system call
 * @task:	task of interest, must be blocked
 *
 * Returns the AUDIT_ARCH_* based on the system call convention in use.
 *
 * It's only valid to call this when @task is stopped on entry to a system
 * call, due to %SYSCALL_WORK_SYSCALL_TRACE, %SYSCALL_WORK_SYSCALL_AUDIT, or
 * %SYSCALL_WORK_SECCOMP.
 *
 * Architectures which permit CONFIG_HAVE_ARCH_SECCOMP_FILTER must
 * provide an implementation of this.
 */
int syscall_get_arch(struct task_struct *task);
#endif	/* _ASM_SYSCALL_H */