| Author | Tokens | Token Proportion | Commits | Commit Proportion |
|---|---|---|---|---|
| Sam Bradshaw | 533 | 56.05% | 3 | 9.68% |
| Asai Thambi S P | 371 | 39.01% | 16 | 51.61% |
| Christoph Hellwig | 27 | 2.84% | 5 | 16.13% |
| Selvan Mani | 6 | 0.63% | 3 | 9.68% |
| Jens Axboe | 5 | 0.53% | 1 | 3.23% |
| Ming Lei | 5 | 0.53% | 1 | 3.23% |
| Arnd Bergmann | 2 | 0.21% | 1 | 3.23% |
| Thomas Gleixner | 2 | 0.21% | 1 | 3.23% |
| Total | 951 | 31 |
/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * mtip32xx.h - Header file for the P320 SSD Block Driver * Copyright (C) 2011 Micron Technology, Inc. * * Portions of this code were derived from works subjected to the * following copyright: * Copyright (C) 2009 Integrated Device Technology, Inc. */ #ifndef __MTIP32XX_H__ #define __MTIP32XX_H__ #include <linux/spinlock.h> #include <linux/rwsem.h> #include <linux/ata.h> #include <linux/interrupt.h> /* Offset of Subsystem Device ID in pci confoguration space */ #define PCI_SUBSYSTEM_DEVICEID 0x2E /* offset of Device Control register in PCIe extended capabilites space */ #define PCIE_CONFIG_EXT_DEVICE_CONTROL_OFFSET 0x48 /* check for erase mode support during secure erase */ #define MTIP_SEC_ERASE_MODE 0x2 /* # of times to retry timed out/failed IOs */ #define MTIP_MAX_RETRIES 2 /* Various timeout values in ms */ #define MTIP_NCQ_CMD_TIMEOUT_MS 15000 #define MTIP_IOCTL_CMD_TIMEOUT_MS 5000 #define MTIP_INT_CMD_TIMEOUT_MS 5000 #define MTIP_QUIESCE_IO_TIMEOUT_MS (MTIP_NCQ_CMD_TIMEOUT_MS * \ (MTIP_MAX_RETRIES + 1)) /* check for timeouts every 500ms */ #define MTIP_TIMEOUT_CHECK_PERIOD 500 /* ftl rebuild */ #define MTIP_FTL_REBUILD_OFFSET 142 #define MTIP_FTL_REBUILD_MAGIC 0xED51 #define MTIP_FTL_REBUILD_TIMEOUT_MS 2400000 /* unaligned IO handling */ #define MTIP_MAX_UNALIGNED_SLOTS 2 /* Macro to extract the tag bit number from a tag value. */ #define MTIP_TAG_BIT(tag) (tag & 0x1F) /* * Macro to extract the tag index from a tag value. The index * is used to access the correct s_active/Command Issue register based * on the tag value. */ #define MTIP_TAG_INDEX(tag) (tag >> 5) /* * Maximum number of scatter gather entries * a single command may have. */ #define MTIP_MAX_SG 504 /* * Maximum number of slot groups (Command Issue & s_active registers) * NOTE: This is the driver maximum; check dd->slot_groups for actual value. */ #define MTIP_MAX_SLOT_GROUPS 8 /* Internal command tag. */ #define MTIP_TAG_INTERNAL 0 /* Micron Vendor ID & P320x SSD Device ID */ #define PCI_VENDOR_ID_MICRON 0x1344 #define P320H_DEVICE_ID 0x5150 #define P320M_DEVICE_ID 0x5151 #define P320S_DEVICE_ID 0x5152 #define P325M_DEVICE_ID 0x5153 #define P420H_DEVICE_ID 0x5160 #define P420M_DEVICE_ID 0x5161 #define P425M_DEVICE_ID 0x5163 /* Driver name and version strings */ #define MTIP_DRV_NAME "mtip32xx" #define MTIP_DRV_VERSION "1.3.1" /* Maximum number of minor device numbers per device. */ #define MTIP_MAX_MINORS 16 /* Maximum number of supported command slots. */ #define MTIP_MAX_COMMAND_SLOTS (MTIP_MAX_SLOT_GROUPS * 32) /* * Per-tag bitfield size in longs. * Linux bit manipulation functions * (i.e. test_and_set_bit, find_next_zero_bit) * manipulate memory in longs, so we try to make the math work. * take the slot groups and find the number of longs, rounding up. * Careful! i386 and x86_64 use different size longs! */ #define U32_PER_LONG (sizeof(long) / sizeof(u32)) #define SLOTBITS_IN_LONGS ((MTIP_MAX_SLOT_GROUPS + \ (U32_PER_LONG-1))/U32_PER_LONG) /* BAR number used to access the HBA registers. */ #define MTIP_ABAR 5 #ifdef DEBUG #define dbg_printk(format, arg...) \ printk(pr_fmt(format), ##arg); #else #define dbg_printk(format, arg...) #endif #define MTIP_DFS_MAX_BUF_SIZE 1024 enum { /* below are bit numbers in 'flags' defined in mtip_port */ MTIP_PF_IC_ACTIVE_BIT = 0, /* pio/ioctl */ MTIP_PF_EH_ACTIVE_BIT = 1, /* error handling */ MTIP_PF_SE_ACTIVE_BIT = 2, /* secure erase */ MTIP_PF_DM_ACTIVE_BIT = 3, /* download microcde */ MTIP_PF_TO_ACTIVE_BIT = 9, /* timeout handling */ MTIP_PF_PAUSE_IO = ((1 << MTIP_PF_IC_ACTIVE_BIT) | (1 << MTIP_PF_EH_ACTIVE_BIT) | (1 << MTIP_PF_SE_ACTIVE_BIT) | (1 << MTIP_PF_DM_ACTIVE_BIT) | (1 << MTIP_PF_TO_ACTIVE_BIT)), MTIP_PF_HOST_CAP_64 = 10, /* cache HOST_CAP_64 */ MTIP_PF_SVC_THD_ACTIVE_BIT = 4, MTIP_PF_ISSUE_CMDS_BIT = 5, MTIP_PF_REBUILD_BIT = 6, MTIP_PF_SVC_THD_STOP_BIT = 8, MTIP_PF_SVC_THD_WORK = ((1 << MTIP_PF_EH_ACTIVE_BIT) | (1 << MTIP_PF_ISSUE_CMDS_BIT) | (1 << MTIP_PF_REBUILD_BIT) | (1 << MTIP_PF_SVC_THD_STOP_BIT) | (1 << MTIP_PF_TO_ACTIVE_BIT)), /* below are bit numbers in 'dd_flag' defined in driver_data */ MTIP_DDF_SEC_LOCK_BIT = 0, MTIP_DDF_REMOVE_PENDING_BIT = 1, MTIP_DDF_OVER_TEMP_BIT = 2, MTIP_DDF_WRITE_PROTECT_BIT = 3, MTIP_DDF_CLEANUP_BIT = 5, MTIP_DDF_RESUME_BIT = 6, MTIP_DDF_INIT_DONE_BIT = 7, MTIP_DDF_REBUILD_FAILED_BIT = 8, MTIP_DDF_STOP_IO = ((1 << MTIP_DDF_REMOVE_PENDING_BIT) | (1 << MTIP_DDF_SEC_LOCK_BIT) | (1 << MTIP_DDF_OVER_TEMP_BIT) | (1 << MTIP_DDF_WRITE_PROTECT_BIT) | (1 << MTIP_DDF_REBUILD_FAILED_BIT)), }; struct smart_attr { u8 attr_id; __le16 flags; u8 cur; u8 worst; __le32 data; u8 res[3]; } __packed; struct mtip_work { struct work_struct work; void *port; int cpu_binding; u32 completed; } ____cacheline_aligned_in_smp; #define DEFINE_HANDLER(group) \ void mtip_workq_sdbf##group(struct work_struct *work) \ { \ struct mtip_work *w = (struct mtip_work *) work; \ mtip_workq_sdbfx(w->port, group, w->completed); \ } /* Register Frame Information Structure (FIS), host to device. */ struct host_to_dev_fis { /* * FIS type. * - 27h Register FIS, host to device. * - 34h Register FIS, device to host. * - 39h DMA Activate FIS, device to host. * - 41h DMA Setup FIS, bi-directional. * - 46h Data FIS, bi-directional. * - 58h BIST Activate FIS, bi-directional. * - 5Fh PIO Setup FIS, device to host. * - A1h Set Device Bits FIS, device to host. */ unsigned char type; unsigned char opts; unsigned char command; unsigned char features; union { unsigned char lba_low; unsigned char sector; }; union { unsigned char lba_mid; unsigned char cyl_low; }; union { unsigned char lba_hi; unsigned char cyl_hi; }; union { unsigned char device; unsigned char head; }; union { unsigned char lba_low_ex; unsigned char sector_ex; }; union { unsigned char lba_mid_ex; unsigned char cyl_low_ex; }; union { unsigned char lba_hi_ex; unsigned char cyl_hi_ex; }; unsigned char features_ex; unsigned char sect_count; unsigned char sect_cnt_ex; unsigned char res2; unsigned char control; unsigned int res3; }; /* Command header structure. */ struct mtip_cmd_hdr { /* * Command options. * - Bits 31:16 Number of PRD entries. * - Bits 15:8 Unused in this implementation. * - Bit 7 Prefetch bit, informs the drive to prefetch PRD entries. * - Bit 6 Write bit, should be set when writing data to the device. * - Bit 5 Unused in this implementation. * - Bits 4:0 Length of the command FIS in DWords (DWord = 4 bytes). */ __le32 opts; /* This field is unsed when using NCQ. */ union { __le32 byte_count; __le32 status; }; /* * Lower 32 bits of the command table address associated with this * header. The command table addresses must be 128 byte aligned. */ __le32 ctba; /* * If 64 bit addressing is used this field is the upper 32 bits * of the command table address associated with this command. */ __le32 ctbau; /* Reserved and unused. */ u32 res[4]; }; /* Command scatter gather structure (PRD). */ struct mtip_cmd_sg { /* * Low 32 bits of the data buffer address. For P320 this * address must be 8 byte aligned signified by bits 2:0 being * set to 0. */ __le32 dba; /* * When 64 bit addressing is used this field is the upper * 32 bits of the data buffer address. */ __le32 dba_upper; /* Unused. */ __le32 reserved; /* * Bit 31: interrupt when this data block has been transferred. * Bits 30..22: reserved * Bits 21..0: byte count (minus 1). For P320 the byte count must be * 8 byte aligned signified by bits 2:0 being set to 1. */ __le32 info; }; struct mtip_port; struct mtip_int_cmd; /* Structure used to describe a command. */ struct mtip_cmd { void *command; /* ptr to command table entry */ dma_addr_t command_dma; /* corresponding physical address */ int scatter_ents; /* Number of scatter list entries used */ int unaligned; /* command is unaligned on 4k boundary */ union { struct scatterlist sg[MTIP_MAX_SG]; /* Scatter list entries */ struct mtip_int_cmd *icmd; }; int retries; /* The number of retries left for this command. */ int direction; /* Data transfer direction */ blk_status_t status; }; /* Structure used to describe a port. */ struct mtip_port { /* Pointer back to the driver data for this port. */ struct driver_data *dd; /* * Used to determine if the data pointed to by the * identify field is valid. */ unsigned long identify_valid; /* Base address of the memory mapped IO for the port. */ void __iomem *mmio; /* Array of pointers to the memory mapped s_active registers. */ void __iomem *s_active[MTIP_MAX_SLOT_GROUPS]; /* Array of pointers to the memory mapped completed registers. */ void __iomem *completed[MTIP_MAX_SLOT_GROUPS]; /* Array of pointers to the memory mapped Command Issue registers. */ void __iomem *cmd_issue[MTIP_MAX_SLOT_GROUPS]; /* * Pointer to the beginning of the command header memory as used * by the driver. */ void *command_list; /* * Pointer to the beginning of the command header memory as used * by the DMA. */ dma_addr_t command_list_dma; /* * Pointer to the beginning of the RX FIS memory as used * by the driver. */ void *rxfis; /* * Pointer to the beginning of the RX FIS memory as used * by the DMA. */ dma_addr_t rxfis_dma; /* * Pointer to the DMA region for RX Fis, Identify, RLE10, and SMART */ void *block1; /* * DMA address of region for RX Fis, Identify, RLE10, and SMART */ dma_addr_t block1_dma; /* * Pointer to the beginning of the identify data memory as used * by the driver. */ u16 *identify; /* * Pointer to the beginning of the identify data memory as used * by the DMA. */ dma_addr_t identify_dma; /* * Pointer to the beginning of a sector buffer that is used * by the driver when issuing internal commands. */ u16 *sector_buffer; /* * Pointer to the beginning of a sector buffer that is used * by the DMA when the driver issues internal commands. */ dma_addr_t sector_buffer_dma; u16 *log_buf; dma_addr_t log_buf_dma; u8 *smart_buf; dma_addr_t smart_buf_dma; /* * used to queue commands when an internal command is in progress * or error handling is active */ unsigned long cmds_to_issue[SLOTBITS_IN_LONGS]; /* Used by mtip_service_thread to wait for an event */ wait_queue_head_t svc_wait; /* * indicates the state of the port. Also, helps the service thread * to determine its action on wake up. */ unsigned long flags; /* * Timer used to complete commands that have been active for too long. */ unsigned long ic_pause_timer; /* Counter to control queue depth of unaligned IOs */ atomic_t cmd_slot_unal; /* Spinlock for working around command-issue bug. */ spinlock_t cmd_issue_lock[MTIP_MAX_SLOT_GROUPS]; }; /* * Driver private data structure. * * One structure is allocated per probed device. */ struct driver_data { void __iomem *mmio; /* Base address of the HBA registers. */ int major; /* Major device number. */ int instance; /* Instance number. First device probed is 0, ... */ struct gendisk *disk; /* Pointer to our gendisk structure. */ struct pci_dev *pdev; /* Pointer to the PCI device structure. */ struct request_queue *queue; /* Our request queue. */ struct blk_mq_tag_set tags; /* blk_mq tags */ struct mtip_port *port; /* Pointer to the port data structure. */ unsigned product_type; /* magic value declaring the product type */ unsigned slot_groups; /* number of slot groups the product supports */ unsigned long index; /* Index to determine the disk name */ unsigned long dd_flag; /* NOTE: use atomic bit operations on this */ struct task_struct *mtip_svc_handler; /* task_struct of svc thd */ struct dentry *dfs_node; bool sr; int numa_node; /* NUMA support */ char workq_name[32]; struct workqueue_struct *isr_workq; atomic_t irq_workers_active; struct mtip_work work[MTIP_MAX_SLOT_GROUPS]; int isr_binding; int unal_qdepth; /* qdepth of unaligned IO queue */ }; #endif
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1