Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Linus Torvalds (pre-git) | 1310 | 46.36% | 40 | 30.08% |
Johan Hovold | 615 | 21.76% | 20 | 15.04% |
Greg Kroah-Hartman | 408 | 14.44% | 29 | 21.80% |
Alan Cox | 129 | 4.56% | 9 | 6.77% |
Linus Torvalds | 116 | 4.10% | 11 | 8.27% |
Joris van Rantwijk | 41 | 1.45% | 1 | 0.75% |
Rusty Russell | 40 | 1.42% | 1 | 0.75% |
David Howells | 36 | 1.27% | 1 | 0.75% |
David Woodhouse | 32 | 1.13% | 1 | 0.75% |
Himadri Pandya | 13 | 0.46% | 1 | 0.75% |
Nathaniel Wesley Filardo | 11 | 0.39% | 1 | 0.75% |
Ben Hutchings | 10 | 0.35% | 1 | 0.75% |
Ingo Molnar | 9 | 0.32% | 1 | 0.75% |
Jiri Slaby | 9 | 0.32% | 3 | 2.26% |
René Bürgel | 9 | 0.32% | 3 | 2.26% |
Mark Knibbs | 8 | 0.28% | 1 | 0.75% |
Harvey Harrison | 7 | 0.25% | 1 | 0.75% |
Jiri Kosina | 6 | 0.21% | 1 | 0.75% |
Nishanth Aravamudan | 6 | 0.21% | 1 | 0.75% |
Ganesh Varadarajan | 5 | 0.18% | 2 | 1.50% |
Márton Németh | 3 | 0.11% | 1 | 0.75% |
Uwe Kleine-König | 1 | 0.04% | 1 | 0.75% |
Oliver Neukum | 1 | 0.04% | 1 | 0.75% |
Ilpo Järvinen | 1 | 0.04% | 1 | 0.75% |
Total | 2826 | 133 |
// SPDX-License-Identifier: GPL-2.0+ /* * USB Keyspan PDA / Xircom / Entrega Converter driver * * Copyright (C) 1999 - 2001 Greg Kroah-Hartman <greg@kroah.com> * Copyright (C) 1999, 2000 Brian Warner <warner@lothar.com> * Copyright (C) 2000 Al Borchers <borchers@steinerpoint.com> * Copyright (C) 2020 Johan Hovold <johan@kernel.org> * * See Documentation/usb/usb-serial.rst for more information on using this * driver */ #include <linux/kernel.h> #include <linux/errno.h> #include <linux/slab.h> #include <linux/tty.h> #include <linux/tty_driver.h> #include <linux/tty_flip.h> #include <linux/module.h> #include <linux/spinlock.h> #include <linux/workqueue.h> #include <linux/uaccess.h> #include <linux/usb.h> #include <linux/usb/serial.h> #include <linux/usb/ezusb.h> #define DRIVER_AUTHOR "Brian Warner <warner@lothar.com>, Johan Hovold <johan@kernel.org>" #define DRIVER_DESC "USB Keyspan PDA Converter driver" #define KEYSPAN_TX_THRESHOLD 128 struct keyspan_pda_private { int tx_room; struct work_struct unthrottle_work; struct usb_serial *serial; struct usb_serial_port *port; }; static int keyspan_pda_write_start(struct usb_serial_port *port); #define KEYSPAN_VENDOR_ID 0x06cd #define KEYSPAN_PDA_FAKE_ID 0x0103 #define KEYSPAN_PDA_ID 0x0104 /* no clue */ /* For Xircom PGSDB9 and older Entrega version of the same device */ #define XIRCOM_VENDOR_ID 0x085a #define XIRCOM_FAKE_ID 0x8027 #define XIRCOM_FAKE_ID_2 0x8025 /* "PGMFHUB" serial */ #define ENTREGA_VENDOR_ID 0x1645 #define ENTREGA_FAKE_ID 0x8093 static const struct usb_device_id id_table_combined[] = { { USB_DEVICE(KEYSPAN_VENDOR_ID, KEYSPAN_PDA_FAKE_ID) }, { USB_DEVICE(XIRCOM_VENDOR_ID, XIRCOM_FAKE_ID) }, { USB_DEVICE(XIRCOM_VENDOR_ID, XIRCOM_FAKE_ID_2) }, { USB_DEVICE(ENTREGA_VENDOR_ID, ENTREGA_FAKE_ID) }, { USB_DEVICE(KEYSPAN_VENDOR_ID, KEYSPAN_PDA_ID) }, { } /* Terminating entry */ }; MODULE_DEVICE_TABLE(usb, id_table_combined); static const struct usb_device_id id_table_std[] = { { USB_DEVICE(KEYSPAN_VENDOR_ID, KEYSPAN_PDA_ID) }, { } /* Terminating entry */ }; static const struct usb_device_id id_table_fake[] = { { USB_DEVICE(KEYSPAN_VENDOR_ID, KEYSPAN_PDA_FAKE_ID) }, { USB_DEVICE(XIRCOM_VENDOR_ID, XIRCOM_FAKE_ID) }, { USB_DEVICE(XIRCOM_VENDOR_ID, XIRCOM_FAKE_ID_2) }, { USB_DEVICE(ENTREGA_VENDOR_ID, ENTREGA_FAKE_ID) }, { } /* Terminating entry */ }; static int keyspan_pda_get_write_room(struct keyspan_pda_private *priv) { struct usb_serial_port *port = priv->port; struct usb_serial *serial = port->serial; u8 room; int rc; rc = usb_control_msg_recv(serial->dev, 0, 6, /* write_room */ USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_IN, 0, /* value: 0 means "remaining room" */ 0, /* index */ &room, 1, 2000, GFP_KERNEL); if (rc) { dev_dbg(&port->dev, "roomquery failed: %d\n", rc); return rc; } dev_dbg(&port->dev, "roomquery says %d\n", room); return room; } static void keyspan_pda_request_unthrottle(struct work_struct *work) { struct keyspan_pda_private *priv = container_of(work, struct keyspan_pda_private, unthrottle_work); struct usb_serial_port *port = priv->port; struct usb_serial *serial = port->serial; unsigned long flags; int result; dev_dbg(&port->dev, "%s\n", __func__); /* * Ask the device to tell us when the tx buffer becomes * sufficiently empty. */ result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 7, /* request_unthrottle */ USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, KEYSPAN_TX_THRESHOLD, 0, /* index */ NULL, 0, 2000); if (result < 0) dev_dbg(&serial->dev->dev, "%s - error %d from usb_control_msg\n", __func__, result); /* * Need to check available space after requesting notification in case * buffer is already empty so that no notification is sent. */ result = keyspan_pda_get_write_room(priv); if (result > KEYSPAN_TX_THRESHOLD) { spin_lock_irqsave(&port->lock, flags); priv->tx_room = max(priv->tx_room, result); spin_unlock_irqrestore(&port->lock, flags); usb_serial_port_softint(port); } } static void keyspan_pda_rx_interrupt(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned char *data = urb->transfer_buffer; unsigned int len = urb->actual_length; int retval; int status = urb->status; struct keyspan_pda_private *priv; unsigned long flags; priv = usb_get_serial_port_data(port); switch (status) { case 0: /* success */ break; case -ECONNRESET: case -ENOENT: case -ESHUTDOWN: /* this urb is terminated, clean up */ dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status); return; default: dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status); goto exit; } if (len < 1) { dev_warn(&port->dev, "short message received\n"); goto exit; } /* see if the message is data or a status interrupt */ switch (data[0]) { case 0: /* rest of message is rx data */ if (len < 2) break; tty_insert_flip_string(&port->port, data + 1, len - 1); tty_flip_buffer_push(&port->port); break; case 1: /* status interrupt */ if (len < 2) { dev_warn(&port->dev, "short interrupt message received\n"); break; } dev_dbg(&port->dev, "rx int, d1=%d\n", data[1]); switch (data[1]) { case 1: /* modemline change */ break; case 2: /* tx unthrottle interrupt */ spin_lock_irqsave(&port->lock, flags); priv->tx_room = max(priv->tx_room, KEYSPAN_TX_THRESHOLD); spin_unlock_irqrestore(&port->lock, flags); keyspan_pda_write_start(port); usb_serial_port_softint(port); break; default: break; } break; default: break; } exit: retval = usb_submit_urb(urb, GFP_ATOMIC); if (retval) dev_err(&port->dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); } static void keyspan_pda_rx_throttle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; /* * Stop receiving characters. We just turn off the URB request, and * let chars pile up in the device. If we're doing hardware * flowcontrol, the device will signal the other end when its buffer * fills up. If we're doing XON/XOFF, this would be a good time to * send an XOFF, although it might make sense to foist that off upon * the device too. */ usb_kill_urb(port->interrupt_in_urb); } static void keyspan_pda_rx_unthrottle(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; /* just restart the receive interrupt URB */ if (usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL)) dev_dbg(&port->dev, "usb_submit_urb(read urb) failed\n"); } static speed_t keyspan_pda_setbaud(struct usb_serial *serial, speed_t baud) { int rc; int bindex; switch (baud) { case 110: bindex = 0; break; case 300: bindex = 1; break; case 1200: bindex = 2; break; case 2400: bindex = 3; break; case 4800: bindex = 4; break; case 9600: bindex = 5; break; case 19200: bindex = 6; break; case 38400: bindex = 7; break; case 57600: bindex = 8; break; case 115200: bindex = 9; break; default: bindex = 5; /* Default to 9600 */ baud = 9600; } rc = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 0, /* set baud */ USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, /* type */ bindex, /* value */ 0, /* index */ NULL, /* &data */ 0, /* size */ 2000); /* timeout */ if (rc < 0) return 0; return baud; } static void keyspan_pda_break_ctl(struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; struct usb_serial *serial = port->serial; int value; int result; if (break_state == -1) value = 1; /* start break */ else value = 0; /* clear break */ result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 4, /* set break */ USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, value, 0, NULL, 0, 2000); if (result < 0) dev_dbg(&port->dev, "%s - error %d from usb_control_msg\n", __func__, result); } static void keyspan_pda_set_termios(struct tty_struct *tty, struct usb_serial_port *port, const struct ktermios *old_termios) { struct usb_serial *serial = port->serial; speed_t speed; /* * cflag specifies lots of stuff: number of stop bits, parity, number * of data bits, baud. What can the device actually handle?: * CSTOPB (1 stop bit or 2) * PARENB (parity) * CSIZE (5bit .. 8bit) * There is minimal hw support for parity (a PSW bit seems to hold the * parity of whatever is in the accumulator). The UART either deals * with 10 bits (start, 8 data, stop) or 11 bits (start, 8 data, * 1 special, stop). So, with firmware changes, we could do: * 8N1: 10 bit * 8N2: 11 bit, extra bit always (mark?) * 8[EOMS]1: 11 bit, extra bit is parity * 7[EOMS]1: 10 bit, b0/b7 is parity * 7[EOMS]2: 11 bit, b0/b7 is parity, extra bit always (mark?) * * HW flow control is dictated by the tty->termios.c_cflags & CRTSCTS * bit. * * For now, just do baud. */ speed = tty_get_baud_rate(tty); speed = keyspan_pda_setbaud(serial, speed); if (speed == 0) { dev_dbg(&port->dev, "can't handle requested baud rate\n"); /* It hasn't changed so.. */ speed = tty_termios_baud_rate(old_termios); } /* * Only speed can change so copy the old h/w parameters then encode * the new speed. */ tty_termios_copy_hw(&tty->termios, old_termios); tty_encode_baud_rate(tty, speed, speed); } /* * Modem control pins: DTR and RTS are outputs and can be controlled. * DCD, RI, DSR, CTS are inputs and can be read. All outputs can also be * read. The byte passed is: DTR(b7) DCD RI DSR CTS RTS(b2) unused unused. */ static int keyspan_pda_get_modem_info(struct usb_serial *serial, unsigned char *value) { int rc; u8 data; rc = usb_control_msg_recv(serial->dev, 0, 3, /* get pins */ USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_IN, 0, 0, &data, 1, 2000, GFP_KERNEL); if (rc == 0) *value = data; return rc; } static int keyspan_pda_set_modem_info(struct usb_serial *serial, unsigned char value) { int rc; rc = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 3, /* set pins */ USB_TYPE_VENDOR|USB_RECIP_INTERFACE|USB_DIR_OUT, value, 0, NULL, 0, 2000); return rc; } static int keyspan_pda_tiocmget(struct tty_struct *tty) { struct usb_serial_port *port = tty->driver_data; struct usb_serial *serial = port->serial; int rc; unsigned char status; int value; rc = keyspan_pda_get_modem_info(serial, &status); if (rc < 0) return rc; value = ((status & BIT(7)) ? TIOCM_DTR : 0) | ((status & BIT(6)) ? TIOCM_CAR : 0) | ((status & BIT(5)) ? TIOCM_RNG : 0) | ((status & BIT(4)) ? TIOCM_DSR : 0) | ((status & BIT(3)) ? TIOCM_CTS : 0) | ((status & BIT(2)) ? TIOCM_RTS : 0); return value; } static int keyspan_pda_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) { struct usb_serial_port *port = tty->driver_data; struct usb_serial *serial = port->serial; int rc; unsigned char status; rc = keyspan_pda_get_modem_info(serial, &status); if (rc < 0) return rc; if (set & TIOCM_RTS) status |= BIT(2); if (set & TIOCM_DTR) status |= BIT(7); if (clear & TIOCM_RTS) status &= ~BIT(2); if (clear & TIOCM_DTR) status &= ~BIT(7); rc = keyspan_pda_set_modem_info(serial, status); return rc; } static int keyspan_pda_write_start(struct usb_serial_port *port) { struct keyspan_pda_private *priv = usb_get_serial_port_data(port); unsigned long flags; struct urb *urb; int count; int room; int rc; /* * Guess how much room is left in the device's ring buffer. If our * write will result in no room left, ask the device to give us an * interrupt when the room available rises above a threshold but also * query how much room is currently available (in case our guess was * too conservative and the buffer is already empty when the * unthrottle work is scheduled). */ /* * We might block because of: * the TX urb is in-flight (wait until it completes) * the device is full (wait until it says there is room) */ spin_lock_irqsave(&port->lock, flags); room = priv->tx_room; count = kfifo_len(&port->write_fifo); if (!test_bit(0, &port->write_urbs_free) || count == 0 || room == 0) { spin_unlock_irqrestore(&port->lock, flags); return 0; } __clear_bit(0, &port->write_urbs_free); if (count > room) count = room; if (count > port->bulk_out_size) count = port->bulk_out_size; urb = port->write_urb; count = kfifo_out(&port->write_fifo, urb->transfer_buffer, count); urb->transfer_buffer_length = count; port->tx_bytes += count; priv->tx_room -= count; spin_unlock_irqrestore(&port->lock, flags); dev_dbg(&port->dev, "%s - count = %d, txroom = %d\n", __func__, count, room); rc = usb_submit_urb(urb, GFP_ATOMIC); if (rc) { dev_dbg(&port->dev, "usb_submit_urb(write bulk) failed\n"); spin_lock_irqsave(&port->lock, flags); port->tx_bytes -= count; priv->tx_room = max(priv->tx_room, room + count); __set_bit(0, &port->write_urbs_free); spin_unlock_irqrestore(&port->lock, flags); return rc; } if (count == room) schedule_work(&priv->unthrottle_work); return count; } static void keyspan_pda_write_bulk_callback(struct urb *urb) { struct usb_serial_port *port = urb->context; unsigned long flags; spin_lock_irqsave(&port->lock, flags); port->tx_bytes -= urb->transfer_buffer_length; __set_bit(0, &port->write_urbs_free); spin_unlock_irqrestore(&port->lock, flags); keyspan_pda_write_start(port); usb_serial_port_softint(port); } static int keyspan_pda_write(struct tty_struct *tty, struct usb_serial_port *port, const unsigned char *buf, int count) { int rc; dev_dbg(&port->dev, "%s - count = %d\n", __func__, count); if (!count) return 0; count = kfifo_in_locked(&port->write_fifo, buf, count, &port->lock); rc = keyspan_pda_write_start(port); if (rc) return rc; return count; } static void keyspan_pda_dtr_rts(struct usb_serial_port *port, int on) { struct usb_serial *serial = port->serial; if (on) keyspan_pda_set_modem_info(serial, BIT(7) | BIT(2)); else keyspan_pda_set_modem_info(serial, 0); } static int keyspan_pda_open(struct tty_struct *tty, struct usb_serial_port *port) { struct keyspan_pda_private *priv = usb_get_serial_port_data(port); int rc; /* find out how much room is in the Tx ring */ rc = keyspan_pda_get_write_room(priv); if (rc < 0) return rc; spin_lock_irq(&port->lock); priv->tx_room = rc; spin_unlock_irq(&port->lock); rc = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL); if (rc) { dev_dbg(&port->dev, "%s - usb_submit_urb(read int) failed\n", __func__); return rc; } return 0; } static void keyspan_pda_close(struct usb_serial_port *port) { struct keyspan_pda_private *priv = usb_get_serial_port_data(port); /* * Stop the interrupt URB first as its completion handler may submit * the write URB. */ usb_kill_urb(port->interrupt_in_urb); usb_kill_urb(port->write_urb); cancel_work_sync(&priv->unthrottle_work); spin_lock_irq(&port->lock); kfifo_reset(&port->write_fifo); spin_unlock_irq(&port->lock); } /* download the firmware to a "fake" device (pre-renumeration) */ static int keyspan_pda_fake_startup(struct usb_serial *serial) { unsigned int vid = le16_to_cpu(serial->dev->descriptor.idVendor); const char *fw_name; /* download the firmware here ... */ ezusb_fx1_set_reset(serial->dev, 1); switch (vid) { case KEYSPAN_VENDOR_ID: fw_name = "keyspan_pda/keyspan_pda.fw"; break; case XIRCOM_VENDOR_ID: case ENTREGA_VENDOR_ID: fw_name = "keyspan_pda/xircom_pgs.fw"; break; default: dev_err(&serial->dev->dev, "%s: unknown vendor, aborting.\n", __func__); return -ENODEV; } if (ezusb_fx1_ihex_firmware_download(serial->dev, fw_name) < 0) { dev_err(&serial->dev->dev, "failed to load firmware \"%s\"\n", fw_name); return -ENOENT; } /* * After downloading firmware renumeration will occur in a moment and * the new device will bind to the real driver. */ /* We want this device to fail to have a driver assigned to it. */ return 1; } MODULE_FIRMWARE("keyspan_pda/keyspan_pda.fw"); MODULE_FIRMWARE("keyspan_pda/xircom_pgs.fw"); static int keyspan_pda_port_probe(struct usb_serial_port *port) { struct keyspan_pda_private *priv; priv = kmalloc(sizeof(struct keyspan_pda_private), GFP_KERNEL); if (!priv) return -ENOMEM; INIT_WORK(&priv->unthrottle_work, keyspan_pda_request_unthrottle); priv->port = port; usb_set_serial_port_data(port, priv); return 0; } static void keyspan_pda_port_remove(struct usb_serial_port *port) { struct keyspan_pda_private *priv; priv = usb_get_serial_port_data(port); kfree(priv); } static struct usb_serial_driver keyspan_pda_fake_device = { .driver = { .owner = THIS_MODULE, .name = "keyspan_pda_pre", }, .description = "Keyspan PDA - (prerenumeration)", .id_table = id_table_fake, .num_ports = 1, .attach = keyspan_pda_fake_startup, }; static struct usb_serial_driver keyspan_pda_device = { .driver = { .owner = THIS_MODULE, .name = "keyspan_pda", }, .description = "Keyspan PDA", .id_table = id_table_std, .num_ports = 1, .num_bulk_out = 1, .num_interrupt_in = 1, .dtr_rts = keyspan_pda_dtr_rts, .open = keyspan_pda_open, .close = keyspan_pda_close, .write = keyspan_pda_write, .write_bulk_callback = keyspan_pda_write_bulk_callback, .read_int_callback = keyspan_pda_rx_interrupt, .throttle = keyspan_pda_rx_throttle, .unthrottle = keyspan_pda_rx_unthrottle, .set_termios = keyspan_pda_set_termios, .break_ctl = keyspan_pda_break_ctl, .tiocmget = keyspan_pda_tiocmget, .tiocmset = keyspan_pda_tiocmset, .port_probe = keyspan_pda_port_probe, .port_remove = keyspan_pda_port_remove, }; static struct usb_serial_driver * const serial_drivers[] = { &keyspan_pda_device, &keyspan_pda_fake_device, NULL }; module_usb_serial_driver(serial_drivers, id_table_combined); MODULE_AUTHOR(DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE("GPL");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1