Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Marek Vašut | 3682 | 99.86% | 2 | 40.00% |
Boris Brezillon | 3 | 0.08% | 1 | 20.00% |
Uwe Kleine-König | 2 | 0.05% | 2 | 40.00% |
Total | 3687 | 5 |
// SPDX-License-Identifier: GPL-2.0 /* * Lontium LT9211 bridge driver * * LT9211 is capable of converting: * 2xDSI/2xLVDS/1xDPI -> 2xDSI/2xLVDS/1xDPI * Currently supported is: * 1xDSI -> 1xLVDS * * Copyright (C) 2022 Marek Vasut <marex@denx.de> */ #include <linux/bits.h> #include <linux/clk.h> #include <linux/gpio/consumer.h> #include <linux/i2c.h> #include <linux/media-bus-format.h> #include <linux/module.h> #include <linux/of_device.h> #include <linux/of_graph.h> #include <linux/regmap.h> #include <linux/regulator/consumer.h> #include <drm/drm_atomic_helper.h> #include <drm/drm_bridge.h> #include <drm/drm_mipi_dsi.h> #include <drm/drm_of.h> #include <drm/drm_panel.h> #include <drm/drm_print.h> #include <drm/drm_probe_helper.h> #define REG_PAGE_CONTROL 0xff #define REG_CHIPID0 0x8100 #define REG_CHIPID0_VALUE 0x18 #define REG_CHIPID1 0x8101 #define REG_CHIPID1_VALUE 0x01 #define REG_CHIPID2 0x8102 #define REG_CHIPID2_VALUE 0xe3 #define REG_DSI_LANE 0xd000 /* DSI lane count - 0 means 4 lanes ; 1, 2, 3 means 1, 2, 3 lanes. */ #define REG_DSI_LANE_COUNT(n) ((n) & 3) struct lt9211 { struct drm_bridge bridge; struct device *dev; struct regmap *regmap; struct mipi_dsi_device *dsi; struct drm_bridge *panel_bridge; struct gpio_desc *reset_gpio; struct regulator *vccio; bool lvds_dual_link; bool lvds_dual_link_even_odd_swap; }; static const struct regmap_range lt9211_rw_ranges[] = { regmap_reg_range(0xff, 0xff), regmap_reg_range(0x8100, 0x816b), regmap_reg_range(0x8200, 0x82aa), regmap_reg_range(0x8500, 0x85ff), regmap_reg_range(0x8600, 0x86a0), regmap_reg_range(0x8700, 0x8746), regmap_reg_range(0xd000, 0xd0a7), regmap_reg_range(0xd400, 0xd42c), regmap_reg_range(0xd800, 0xd838), regmap_reg_range(0xd9c0, 0xd9d5), }; static const struct regmap_access_table lt9211_rw_table = { .yes_ranges = lt9211_rw_ranges, .n_yes_ranges = ARRAY_SIZE(lt9211_rw_ranges), }; static const struct regmap_range_cfg lt9211_range = { .name = "lt9211", .range_min = 0x0000, .range_max = 0xda00, .selector_reg = REG_PAGE_CONTROL, .selector_mask = 0xff, .selector_shift = 0, .window_start = 0, .window_len = 0x100, }; static const struct regmap_config lt9211_regmap_config = { .reg_bits = 8, .val_bits = 8, .rd_table = <9211_rw_table, .wr_table = <9211_rw_table, .volatile_table = <9211_rw_table, .ranges = <9211_range, .num_ranges = 1, .cache_type = REGCACHE_RBTREE, .max_register = 0xda00, }; static struct lt9211 *bridge_to_lt9211(struct drm_bridge *bridge) { return container_of(bridge, struct lt9211, bridge); } static int lt9211_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags) { struct lt9211 *ctx = bridge_to_lt9211(bridge); return drm_bridge_attach(bridge->encoder, ctx->panel_bridge, &ctx->bridge, flags); } static int lt9211_read_chipid(struct lt9211 *ctx) { u8 chipid[3]; int ret; /* Read Chip ID registers and verify the chip can communicate. */ ret = regmap_bulk_read(ctx->regmap, REG_CHIPID0, chipid, 3); if (ret < 0) { dev_err(ctx->dev, "Failed to read Chip ID: %d\n", ret); return ret; } /* Test for known Chip ID. */ if (chipid[0] != REG_CHIPID0_VALUE || chipid[1] != REG_CHIPID1_VALUE || chipid[2] != REG_CHIPID2_VALUE) { dev_err(ctx->dev, "Unknown Chip ID: 0x%02x 0x%02x 0x%02x\n", chipid[0], chipid[1], chipid[2]); return -EINVAL; } return 0; } static int lt9211_system_init(struct lt9211 *ctx) { const struct reg_sequence lt9211_system_init_seq[] = { { 0x8201, 0x18 }, { 0x8606, 0x61 }, { 0x8607, 0xa8 }, { 0x8714, 0x08 }, { 0x8715, 0x00 }, { 0x8718, 0x0f }, { 0x8722, 0x08 }, { 0x8723, 0x00 }, { 0x8726, 0x0f }, { 0x810b, 0xfe }, }; return regmap_multi_reg_write(ctx->regmap, lt9211_system_init_seq, ARRAY_SIZE(lt9211_system_init_seq)); } static int lt9211_configure_rx(struct lt9211 *ctx) { const struct reg_sequence lt9211_rx_phy_seq[] = { { 0x8202, 0x44 }, { 0x8204, 0xa0 }, { 0x8205, 0x22 }, { 0x8207, 0x9f }, { 0x8208, 0xfc }, /* ORR with 0xf8 here to enable DSI DN/DP swap. */ { 0x8209, 0x01 }, { 0x8217, 0x0c }, { 0x8633, 0x1b }, }; const struct reg_sequence lt9211_rx_cal_reset_seq[] = { { 0x8120, 0x7f }, { 0x8120, 0xff }, }; const struct reg_sequence lt9211_rx_dig_seq[] = { { 0x8630, 0x85 }, /* 0x8588: BIT 6 set = MIPI-RX, BIT 4 unset = LVDS-TX */ { 0x8588, 0x40 }, { 0x85ff, 0xd0 }, { REG_DSI_LANE, REG_DSI_LANE_COUNT(ctx->dsi->lanes) }, { 0xd002, 0x05 }, }; const struct reg_sequence lt9211_rx_div_reset_seq[] = { { 0x810a, 0xc0 }, { 0x8120, 0xbf }, }; const struct reg_sequence lt9211_rx_div_clear_seq[] = { { 0x810a, 0xc1 }, { 0x8120, 0xff }, }; int ret; ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_phy_seq, ARRAY_SIZE(lt9211_rx_phy_seq)); if (ret) return ret; ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_cal_reset_seq, ARRAY_SIZE(lt9211_rx_cal_reset_seq)); if (ret) return ret; ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_dig_seq, ARRAY_SIZE(lt9211_rx_dig_seq)); if (ret) return ret; ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_div_reset_seq, ARRAY_SIZE(lt9211_rx_div_reset_seq)); if (ret) return ret; usleep_range(10000, 15000); return regmap_multi_reg_write(ctx->regmap, lt9211_rx_div_clear_seq, ARRAY_SIZE(lt9211_rx_div_clear_seq)); } static int lt9211_autodetect_rx(struct lt9211 *ctx, const struct drm_display_mode *mode) { u16 width, height; u32 byteclk; u8 buf[5]; u8 format; u8 bc[3]; int ret; /* Measure ByteClock frequency. */ ret = regmap_write(ctx->regmap, 0x8600, 0x01); if (ret) return ret; /* Give the chip time to lock onto RX stream. */ msleep(100); /* Read the ByteClock frequency from the chip. */ ret = regmap_bulk_read(ctx->regmap, 0x8608, bc, sizeof(bc)); if (ret) return ret; /* RX ByteClock in kHz */ byteclk = ((bc[0] & 0xf) << 16) | (bc[1] << 8) | bc[2]; /* Width/Height/Format Auto-detection */ ret = regmap_bulk_read(ctx->regmap, 0xd082, buf, sizeof(buf)); if (ret) return ret; width = (buf[0] << 8) | buf[1]; height = (buf[3] << 8) | buf[4]; format = buf[2] & 0xf; if (format == 0x3) { /* YUV422 16bit */ width /= 2; } else if (format == 0xa) { /* RGB888 24bit */ width /= 3; } else { dev_err(ctx->dev, "Unsupported DSI pixel format 0x%01x\n", format); return -EINVAL; } if (width != mode->hdisplay) { dev_err(ctx->dev, "RX: Detected DSI width (%d) does not match mode hdisplay (%d)\n", width, mode->hdisplay); return -EINVAL; } if (height != mode->vdisplay) { dev_err(ctx->dev, "RX: Detected DSI height (%d) does not match mode vdisplay (%d)\n", height, mode->vdisplay); return -EINVAL; } dev_dbg(ctx->dev, "RX: %dx%d format=0x%01x byteclock=%d kHz\n", width, height, format, byteclk); return 0; } static int lt9211_configure_timing(struct lt9211 *ctx, const struct drm_display_mode *mode) { const struct reg_sequence lt9211_timing[] = { { 0xd00d, (mode->vtotal >> 8) & 0xff }, { 0xd00e, mode->vtotal & 0xff }, { 0xd00f, (mode->vdisplay >> 8) & 0xff }, { 0xd010, mode->vdisplay & 0xff }, { 0xd011, (mode->htotal >> 8) & 0xff }, { 0xd012, mode->htotal & 0xff }, { 0xd013, (mode->hdisplay >> 8) & 0xff }, { 0xd014, mode->hdisplay & 0xff }, { 0xd015, (mode->vsync_end - mode->vsync_start) & 0xff }, { 0xd016, (mode->hsync_end - mode->hsync_start) & 0xff }, { 0xd017, ((mode->vsync_start - mode->vdisplay) >> 8) & 0xff }, { 0xd018, (mode->vsync_start - mode->vdisplay) & 0xff }, { 0xd019, ((mode->hsync_start - mode->hdisplay) >> 8) & 0xff }, { 0xd01a, (mode->hsync_start - mode->hdisplay) & 0xff }, }; return regmap_multi_reg_write(ctx->regmap, lt9211_timing, ARRAY_SIZE(lt9211_timing)); } static int lt9211_configure_plls(struct lt9211 *ctx, const struct drm_display_mode *mode) { const struct reg_sequence lt9211_pcr_seq[] = { { 0xd026, 0x17 }, { 0xd027, 0xc3 }, { 0xd02d, 0x30 }, { 0xd031, 0x10 }, { 0xd023, 0x20 }, { 0xd038, 0x02 }, { 0xd039, 0x10 }, { 0xd03a, 0x20 }, { 0xd03b, 0x60 }, { 0xd03f, 0x04 }, { 0xd040, 0x08 }, { 0xd041, 0x10 }, { 0x810b, 0xee }, { 0x810b, 0xfe }, }; unsigned int pval; int ret; /* DeSSC PLL reference clock is 25 MHz XTal. */ ret = regmap_write(ctx->regmap, 0x822d, 0x48); if (ret) return ret; if (mode->clock < 44000) { ret = regmap_write(ctx->regmap, 0x8235, 0x83); } else if (mode->clock < 88000) { ret = regmap_write(ctx->regmap, 0x8235, 0x82); } else if (mode->clock < 176000) { ret = regmap_write(ctx->regmap, 0x8235, 0x81); } else { dev_err(ctx->dev, "Unsupported mode clock (%d kHz) above 176 MHz.\n", mode->clock); return -EINVAL; } if (ret) return ret; /* Wait for the DeSSC PLL to stabilize. */ msleep(100); ret = regmap_multi_reg_write(ctx->regmap, lt9211_pcr_seq, ARRAY_SIZE(lt9211_pcr_seq)); if (ret) return ret; /* PCR stability test takes seconds. */ ret = regmap_read_poll_timeout(ctx->regmap, 0xd087, pval, pval & 0x8, 20000, 10000000); if (ret) dev_err(ctx->dev, "PCR unstable, ret=%i\n", ret); return ret; } static int lt9211_configure_tx(struct lt9211 *ctx, bool jeida, bool bpp24, bool de) { const struct reg_sequence system_lt9211_tx_phy_seq[] = { /* DPI output disable */ { 0x8262, 0x00 }, /* BIT(7) is LVDS dual-port */ { 0x823b, 0x38 | (ctx->lvds_dual_link ? BIT(7) : 0) }, { 0x823e, 0x92 }, { 0x823f, 0x48 }, { 0x8240, 0x31 }, { 0x8243, 0x80 }, { 0x8244, 0x00 }, { 0x8245, 0x00 }, { 0x8249, 0x00 }, { 0x824a, 0x01 }, { 0x824e, 0x00 }, { 0x824f, 0x00 }, { 0x8250, 0x00 }, { 0x8253, 0x00 }, { 0x8254, 0x01 }, /* LVDS channel order, Odd:Even 0x10..A:B, 0x40..B:A */ { 0x8646, ctx->lvds_dual_link_even_odd_swap ? 0x40 : 0x10 }, { 0x8120, 0x7b }, { 0x816b, 0xff }, }; const struct reg_sequence system_lt9211_tx_dig_seq[] = { { 0x8559, 0x40 | (jeida ? BIT(7) : 0) | (de ? BIT(5) : 0) | (bpp24 ? BIT(4) : 0) }, { 0x855a, 0xaa }, { 0x855b, 0xaa }, { 0x855c, ctx->lvds_dual_link ? BIT(0) : 0 }, { 0x85a1, 0x77 }, { 0x8640, 0x40 }, { 0x8641, 0x34 }, { 0x8642, 0x10 }, { 0x8643, 0x23 }, { 0x8644, 0x41 }, { 0x8645, 0x02 }, }; const struct reg_sequence system_lt9211_tx_pll_seq[] = { /* TX PLL power down */ { 0x8236, 0x01 }, { 0x8237, ctx->lvds_dual_link ? 0x2a : 0x29 }, { 0x8238, 0x06 }, { 0x8239, 0x30 }, { 0x823a, 0x8e }, { 0x8737, 0x14 }, { 0x8713, 0x00 }, { 0x8713, 0x80 }, }; unsigned int pval; int ret; ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_phy_seq, ARRAY_SIZE(system_lt9211_tx_phy_seq)); if (ret) return ret; ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_dig_seq, ARRAY_SIZE(system_lt9211_tx_dig_seq)); if (ret) return ret; ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_pll_seq, ARRAY_SIZE(system_lt9211_tx_pll_seq)); if (ret) return ret; ret = regmap_read_poll_timeout(ctx->regmap, 0x871f, pval, pval & 0x80, 10000, 1000000); if (ret) { dev_err(ctx->dev, "TX PLL unstable, ret=%i\n", ret); return ret; } ret = regmap_read_poll_timeout(ctx->regmap, 0x8720, pval, pval & 0x80, 10000, 1000000); if (ret) { dev_err(ctx->dev, "TX PLL unstable, ret=%i\n", ret); return ret; } return 0; } static void lt9211_atomic_enable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state) { struct lt9211 *ctx = bridge_to_lt9211(bridge); struct drm_atomic_state *state = old_bridge_state->base.state; const struct drm_bridge_state *bridge_state; const struct drm_crtc_state *crtc_state; const struct drm_display_mode *mode; struct drm_connector *connector; struct drm_crtc *crtc; bool lvds_format_24bpp; bool lvds_format_jeida; u32 bus_flags; int ret; ret = regulator_enable(ctx->vccio); if (ret) { dev_err(ctx->dev, "Failed to enable vccio: %d\n", ret); return; } /* Deassert reset */ gpiod_set_value(ctx->reset_gpio, 1); usleep_range(20000, 21000); /* Very long post-reset delay. */ /* Get the LVDS format from the bridge state. */ bridge_state = drm_atomic_get_new_bridge_state(state, bridge); bus_flags = bridge_state->output_bus_cfg.flags; switch (bridge_state->output_bus_cfg.format) { case MEDIA_BUS_FMT_RGB666_1X7X3_SPWG: lvds_format_24bpp = false; lvds_format_jeida = true; break; case MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA: lvds_format_24bpp = true; lvds_format_jeida = true; break; case MEDIA_BUS_FMT_RGB888_1X7X4_SPWG: lvds_format_24bpp = true; lvds_format_jeida = false; break; default: /* * Some bridges still don't set the correct * LVDS bus pixel format, use SPWG24 default * format until those are fixed. */ lvds_format_24bpp = true; lvds_format_jeida = false; dev_warn(ctx->dev, "Unsupported LVDS bus format 0x%04x, please check output bridge driver. Falling back to SPWG24.\n", bridge_state->output_bus_cfg.format); break; } /* * Retrieve the CRTC adjusted mode. This requires a little dance to go * from the bridge to the encoder, to the connector and to the CRTC. */ connector = drm_atomic_get_new_connector_for_encoder(state, bridge->encoder); crtc = drm_atomic_get_new_connector_state(state, connector)->crtc; crtc_state = drm_atomic_get_new_crtc_state(state, crtc); mode = &crtc_state->adjusted_mode; ret = lt9211_read_chipid(ctx); if (ret) return; ret = lt9211_system_init(ctx); if (ret) return; ret = lt9211_configure_rx(ctx); if (ret) return; ret = lt9211_autodetect_rx(ctx, mode); if (ret) return; ret = lt9211_configure_timing(ctx, mode); if (ret) return; ret = lt9211_configure_plls(ctx, mode); if (ret) return; ret = lt9211_configure_tx(ctx, lvds_format_jeida, lvds_format_24bpp, bus_flags & DRM_BUS_FLAG_DE_HIGH); if (ret) return; dev_dbg(ctx->dev, "LT9211 enabled.\n"); } static void lt9211_atomic_disable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state) { struct lt9211 *ctx = bridge_to_lt9211(bridge); int ret; /* * Put the chip in reset, pull nRST line low, * and assure lengthy 10ms reset low timing. */ gpiod_set_value(ctx->reset_gpio, 0); usleep_range(10000, 11000); /* Very long reset duration. */ ret = regulator_disable(ctx->vccio); if (ret) dev_err(ctx->dev, "Failed to disable vccio: %d\n", ret); regcache_mark_dirty(ctx->regmap); } static enum drm_mode_status lt9211_mode_valid(struct drm_bridge *bridge, const struct drm_display_info *info, const struct drm_display_mode *mode) { /* LVDS output clock range 25..176 MHz */ if (mode->clock < 25000) return MODE_CLOCK_LOW; if (mode->clock > 176000) return MODE_CLOCK_HIGH; return MODE_OK; } #define MAX_INPUT_SEL_FORMATS 1 static u32 * lt9211_atomic_get_input_bus_fmts(struct drm_bridge *bridge, struct drm_bridge_state *bridge_state, struct drm_crtc_state *crtc_state, struct drm_connector_state *conn_state, u32 output_fmt, unsigned int *num_input_fmts) { u32 *input_fmts; *num_input_fmts = 0; input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), GFP_KERNEL); if (!input_fmts) return NULL; /* This is the DSI-end bus format */ input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; *num_input_fmts = 1; return input_fmts; } static const struct drm_bridge_funcs lt9211_funcs = { .attach = lt9211_attach, .mode_valid = lt9211_mode_valid, .atomic_enable = lt9211_atomic_enable, .atomic_disable = lt9211_atomic_disable, .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, .atomic_get_input_bus_fmts = lt9211_atomic_get_input_bus_fmts, .atomic_reset = drm_atomic_helper_bridge_reset, }; static int lt9211_parse_dt(struct lt9211 *ctx) { struct device_node *port2, *port3; struct drm_bridge *panel_bridge; struct device *dev = ctx->dev; struct drm_panel *panel; int dual_link; int ret; ctx->vccio = devm_regulator_get(dev, "vccio"); if (IS_ERR(ctx->vccio)) return dev_err_probe(dev, PTR_ERR(ctx->vccio), "Failed to get supply 'vccio'\n"); ctx->lvds_dual_link = false; ctx->lvds_dual_link_even_odd_swap = false; port2 = of_graph_get_port_by_id(dev->of_node, 2); port3 = of_graph_get_port_by_id(dev->of_node, 3); dual_link = drm_of_lvds_get_dual_link_pixel_order(port2, port3); of_node_put(port2); of_node_put(port3); if (dual_link == DRM_LVDS_DUAL_LINK_ODD_EVEN_PIXELS) { ctx->lvds_dual_link = true; /* Odd pixels to LVDS Channel A, even pixels to B */ ctx->lvds_dual_link_even_odd_swap = false; } else if (dual_link == DRM_LVDS_DUAL_LINK_EVEN_ODD_PIXELS) { ctx->lvds_dual_link = true; /* Even pixels to LVDS Channel A, odd pixels to B */ ctx->lvds_dual_link_even_odd_swap = true; } ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, &panel_bridge); if (ret < 0) return ret; if (panel) { panel_bridge = devm_drm_panel_bridge_add(dev, panel); if (IS_ERR(panel_bridge)) return PTR_ERR(panel_bridge); } ctx->panel_bridge = panel_bridge; return 0; } static int lt9211_host_attach(struct lt9211 *ctx) { const struct mipi_dsi_device_info info = { .type = "lt9211", .channel = 0, .node = NULL, }; struct device *dev = ctx->dev; struct device_node *host_node; struct device_node *endpoint; struct mipi_dsi_device *dsi; struct mipi_dsi_host *host; int dsi_lanes; int ret; endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, -1); dsi_lanes = drm_of_get_data_lanes_count(endpoint, 1, 4); host_node = of_graph_get_remote_port_parent(endpoint); host = of_find_mipi_dsi_host_by_node(host_node); of_node_put(host_node); of_node_put(endpoint); if (!host) return -EPROBE_DEFER; if (dsi_lanes < 0) return dsi_lanes; dsi = devm_mipi_dsi_device_register_full(dev, host, &info); if (IS_ERR(dsi)) return dev_err_probe(dev, PTR_ERR(dsi), "failed to create dsi device\n"); ctx->dsi = dsi; dsi->lanes = dsi_lanes; dsi->format = MIPI_DSI_FMT_RGB888; dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE | MIPI_DSI_MODE_VIDEO_HSE; ret = devm_mipi_dsi_attach(dev, dsi); if (ret < 0) { dev_err(dev, "failed to attach dsi to host: %d\n", ret); return ret; } return 0; } static int lt9211_probe(struct i2c_client *client) { struct device *dev = &client->dev; struct lt9211 *ctx; int ret; ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); if (!ctx) return -ENOMEM; ctx->dev = dev; /* * Put the chip in reset, pull nRST line low, * and assure lengthy 10ms reset low timing. */ ctx->reset_gpio = devm_gpiod_get_optional(ctx->dev, "reset", GPIOD_OUT_LOW); if (IS_ERR(ctx->reset_gpio)) return PTR_ERR(ctx->reset_gpio); usleep_range(10000, 11000); /* Very long reset duration. */ ret = lt9211_parse_dt(ctx); if (ret) return ret; ctx->regmap = devm_regmap_init_i2c(client, <9211_regmap_config); if (IS_ERR(ctx->regmap)) return PTR_ERR(ctx->regmap); dev_set_drvdata(dev, ctx); i2c_set_clientdata(client, ctx); ctx->bridge.funcs = <9211_funcs; ctx->bridge.of_node = dev->of_node; drm_bridge_add(&ctx->bridge); ret = lt9211_host_attach(ctx); if (ret) drm_bridge_remove(&ctx->bridge); return ret; } static void lt9211_remove(struct i2c_client *client) { struct lt9211 *ctx = i2c_get_clientdata(client); drm_bridge_remove(&ctx->bridge); } static struct i2c_device_id lt9211_id[] = { { "lontium,lt9211" }, {}, }; MODULE_DEVICE_TABLE(i2c, lt9211_id); static const struct of_device_id lt9211_match_table[] = { { .compatible = "lontium,lt9211" }, {}, }; MODULE_DEVICE_TABLE(of, lt9211_match_table); static struct i2c_driver lt9211_driver = { .probe_new = lt9211_probe, .remove = lt9211_remove, .id_table = lt9211_id, .driver = { .name = "lt9211", .of_match_table = lt9211_match_table, }, }; module_i2c_driver(lt9211_driver); MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); MODULE_DESCRIPTION("Lontium LT9211 DSI/LVDS/DPI bridge driver"); MODULE_LICENSE("GPL");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1