Contributors: 15
| Author |
Tokens |
Token Proportion |
Commits |
Commit Proportion |
| MyungJoo Ham |
880 |
57.07% |
1 |
3.45% |
| Tomasz Figa |
342 |
22.18% |
2 |
6.90% |
| Linus Walleij |
158 |
10.25% |
4 |
13.79% |
| Axel Lin |
90 |
5.84% |
9 |
31.03% |
| Mark Brown |
32 |
2.08% |
2 |
6.90% |
| Krzysztof Kozlowski |
23 |
1.49% |
1 |
3.45% |
| Jingoo Han |
5 |
0.32% |
2 |
6.90% |
| Javier Martinez Canillas |
3 |
0.19% |
1 |
3.45% |
| Thomas Gleixner |
2 |
0.13% |
1 |
3.45% |
| Markus Pargmann |
2 |
0.13% |
1 |
3.45% |
| Bhumika Goyal |
1 |
0.06% |
1 |
3.45% |
| Lucas De Marchi |
1 |
0.06% |
1 |
3.45% |
| Wolfram Sang |
1 |
0.06% |
1 |
3.45% |
| Uwe Kleine-König |
1 |
0.06% |
1 |
3.45% |
| Rajendra Nayak |
1 |
0.06% |
1 |
3.45% |
| Total |
1542 |
|
29 |
|
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* max8952.c - Voltage and current regulation for the Maxim 8952
*
* Copyright (C) 2010 Samsung Electronics
* MyungJoo Ham <myungjoo.ham@samsung.com>
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/i2c.h>
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/max8952.h>
#include <linux/gpio/consumer.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/regulator/of_regulator.h>
#include <linux/slab.h>
/* Registers */
enum {
MAX8952_REG_MODE0,
MAX8952_REG_MODE1,
MAX8952_REG_MODE2,
MAX8952_REG_MODE3,
MAX8952_REG_CONTROL,
MAX8952_REG_SYNC,
MAX8952_REG_RAMP,
MAX8952_REG_CHIP_ID1,
MAX8952_REG_CHIP_ID2,
};
struct max8952_data {
struct i2c_client *client;
struct max8952_platform_data *pdata;
struct gpio_desc *vid0_gpiod;
struct gpio_desc *vid1_gpiod;
bool vid0;
bool vid1;
};
static int max8952_read_reg(struct max8952_data *max8952, u8 reg)
{
int ret = i2c_smbus_read_byte_data(max8952->client, reg);
if (ret > 0)
ret &= 0xff;
return ret;
}
static int max8952_write_reg(struct max8952_data *max8952,
u8 reg, u8 value)
{
return i2c_smbus_write_byte_data(max8952->client, reg, value);
}
static int max8952_list_voltage(struct regulator_dev *rdev,
unsigned int selector)
{
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
if (rdev_get_id(rdev) != 0)
return -EINVAL;
return (max8952->pdata->dvs_mode[selector] * 10 + 770) * 1000;
}
static int max8952_get_voltage_sel(struct regulator_dev *rdev)
{
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
u8 vid = 0;
if (max8952->vid0)
vid += 1;
if (max8952->vid1)
vid += 2;
return vid;
}
static int max8952_set_voltage_sel(struct regulator_dev *rdev,
unsigned selector)
{
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
if (!max8952->vid0_gpiod || !max8952->vid1_gpiod) {
/* DVS not supported */
return -EPERM;
}
max8952->vid0 = selector & 0x1;
max8952->vid1 = (selector >> 1) & 0x1;
gpiod_set_value(max8952->vid0_gpiod, max8952->vid0);
gpiod_set_value(max8952->vid1_gpiod, max8952->vid1);
return 0;
}
static const struct regulator_ops max8952_ops = {
.list_voltage = max8952_list_voltage,
.get_voltage_sel = max8952_get_voltage_sel,
.set_voltage_sel = max8952_set_voltage_sel,
};
static const struct regulator_desc regulator = {
.name = "MAX8952_VOUT",
.id = 0,
.n_voltages = MAX8952_NUM_DVS_MODE,
.ops = &max8952_ops,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
};
#ifdef CONFIG_OF
static const struct of_device_id max8952_dt_match[] = {
{ .compatible = "maxim,max8952" },
{},
};
MODULE_DEVICE_TABLE(of, max8952_dt_match);
static struct max8952_platform_data *max8952_parse_dt(struct device *dev)
{
struct max8952_platform_data *pd;
struct device_node *np = dev->of_node;
int ret;
int i;
pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
if (!pd)
return NULL;
if (of_property_read_u32(np, "max8952,default-mode", &pd->default_mode))
dev_warn(dev, "Default mode not specified, assuming 0\n");
ret = of_property_read_u32_array(np, "max8952,dvs-mode-microvolt",
pd->dvs_mode, ARRAY_SIZE(pd->dvs_mode));
if (ret) {
dev_err(dev, "max8952,dvs-mode-microvolt property not specified");
return NULL;
}
for (i = 0; i < ARRAY_SIZE(pd->dvs_mode); ++i) {
if (pd->dvs_mode[i] < 770000 || pd->dvs_mode[i] > 1400000) {
dev_err(dev, "DVS voltage %d out of range\n", i);
return NULL;
}
pd->dvs_mode[i] = (pd->dvs_mode[i] - 770000) / 10000;
}
if (of_property_read_u32(np, "max8952,sync-freq", &pd->sync_freq))
dev_warn(dev, "max8952,sync-freq property not specified, defaulting to 26MHz\n");
if (of_property_read_u32(np, "max8952,ramp-speed", &pd->ramp_speed))
dev_warn(dev, "max8952,ramp-speed property not specified, defaulting to 32mV/us\n");
pd->reg_data = of_get_regulator_init_data(dev, np, ®ulator);
if (!pd->reg_data) {
dev_err(dev, "Failed to parse regulator init data\n");
return NULL;
}
return pd;
}
#else
static struct max8952_platform_data *max8952_parse_dt(struct device *dev)
{
return NULL;
}
#endif
static int max8952_pmic_probe(struct i2c_client *client)
{
struct i2c_adapter *adapter = client->adapter;
struct max8952_platform_data *pdata = dev_get_platdata(&client->dev);
struct regulator_config config = { };
struct max8952_data *max8952;
struct regulator_dev *rdev;
struct gpio_desc *gpiod;
enum gpiod_flags gflags;
int ret = 0;
if (client->dev.of_node)
pdata = max8952_parse_dt(&client->dev);
if (!pdata) {
dev_err(&client->dev, "Require the platform data\n");
return -EINVAL;
}
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
return -EIO;
max8952 = devm_kzalloc(&client->dev, sizeof(struct max8952_data),
GFP_KERNEL);
if (!max8952)
return -ENOMEM;
max8952->client = client;
max8952->pdata = pdata;
config.dev = &client->dev;
config.init_data = pdata->reg_data;
config.driver_data = max8952;
config.of_node = client->dev.of_node;
if (pdata->reg_data->constraints.boot_on)
gflags = GPIOD_OUT_HIGH;
else
gflags = GPIOD_OUT_LOW;
gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
/*
* Do not use devm* here: the regulator core takes over the
* lifecycle management of the GPIO descriptor.
*/
gpiod = gpiod_get_optional(&client->dev,
"max8952,en",
gflags);
if (IS_ERR(gpiod))
return PTR_ERR(gpiod);
if (gpiod)
config.ena_gpiod = gpiod;
rdev = devm_regulator_register(&client->dev, ®ulator, &config);
if (IS_ERR(rdev)) {
ret = PTR_ERR(rdev);
dev_err(&client->dev, "regulator init failed (%d)\n", ret);
return ret;
}
max8952->vid0 = pdata->default_mode & 0x1;
max8952->vid1 = (pdata->default_mode >> 1) & 0x1;
/* Fetch vid0 and vid1 GPIOs if available */
gflags = max8952->vid0 ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW;
max8952->vid0_gpiod = devm_gpiod_get_index_optional(&client->dev,
"max8952,vid",
0, gflags);
if (IS_ERR(max8952->vid0_gpiod))
return PTR_ERR(max8952->vid0_gpiod);
gflags = max8952->vid1 ? GPIOD_OUT_HIGH : GPIOD_OUT_LOW;
max8952->vid1_gpiod = devm_gpiod_get_index_optional(&client->dev,
"max8952,vid",
1, gflags);
if (IS_ERR(max8952->vid1_gpiod))
return PTR_ERR(max8952->vid1_gpiod);
/* If either VID GPIO is missing just disable this */
if (!max8952->vid0_gpiod || !max8952->vid1_gpiod) {
dev_warn(&client->dev, "VID0/1 gpio invalid: "
"DVS not available.\n");
max8952->vid0 = 0;
max8952->vid1 = 0;
/* Make sure if we have any descriptors they get set to low */
if (max8952->vid0_gpiod)
gpiod_set_value(max8952->vid0_gpiod, 0);
if (max8952->vid1_gpiod)
gpiod_set_value(max8952->vid1_gpiod, 0);
/* Disable Pulldown of EN only */
max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x60);
dev_err(&client->dev, "DVS modes disabled because VID0 and VID1"
" do not have proper controls.\n");
} else {
/*
* Disable Pulldown on EN, VID0, VID1 to reduce
* leakage current of MAX8952 assuming that MAX8952
* is turned on (EN==1). Note that without having VID0/1
* properly connected, turning pulldown off can be
* problematic. Thus, turn this off only when they are
* controllable by GPIO.
*/
max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x0);
}
max8952_write_reg(max8952, MAX8952_REG_MODE0,
(max8952_read_reg(max8952,
MAX8952_REG_MODE0) & 0xC0) |
(pdata->dvs_mode[0] & 0x3F));
max8952_write_reg(max8952, MAX8952_REG_MODE1,
(max8952_read_reg(max8952,
MAX8952_REG_MODE1) & 0xC0) |
(pdata->dvs_mode[1] & 0x3F));
max8952_write_reg(max8952, MAX8952_REG_MODE2,
(max8952_read_reg(max8952,
MAX8952_REG_MODE2) & 0xC0) |
(pdata->dvs_mode[2] & 0x3F));
max8952_write_reg(max8952, MAX8952_REG_MODE3,
(max8952_read_reg(max8952,
MAX8952_REG_MODE3) & 0xC0) |
(pdata->dvs_mode[3] & 0x3F));
max8952_write_reg(max8952, MAX8952_REG_SYNC,
(max8952_read_reg(max8952, MAX8952_REG_SYNC) & 0x3F) |
((pdata->sync_freq & 0x3) << 6));
max8952_write_reg(max8952, MAX8952_REG_RAMP,
(max8952_read_reg(max8952, MAX8952_REG_RAMP) & 0x1F) |
((pdata->ramp_speed & 0x7) << 5));
i2c_set_clientdata(client, max8952);
return 0;
}
static const struct i2c_device_id max8952_ids[] = {
{ "max8952", 0 },
{ },
};
MODULE_DEVICE_TABLE(i2c, max8952_ids);
static struct i2c_driver max8952_pmic_driver = {
.probe_new = max8952_pmic_probe,
.driver = {
.name = "max8952",
.of_match_table = of_match_ptr(max8952_dt_match),
},
.id_table = max8952_ids,
};
static int __init max8952_pmic_init(void)
{
return i2c_add_driver(&max8952_pmic_driver);
}
subsys_initcall(max8952_pmic_init);
static void __exit max8952_pmic_exit(void)
{
i2c_del_driver(&max8952_pmic_driver);
}
module_exit(max8952_pmic_exit);
MODULE_DESCRIPTION("MAXIM 8952 voltage regulator driver");
MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
MODULE_LICENSE("GPL");