| Author | Tokens | Token Proportion | Commits | Commit Proportion |
|---|---|---|---|---|
| Auke-Jan H Kok | 1780 | 71.69% | 2 | 3.45% |
| Bruce W Allan | 528 | 21.26% | 37 | 63.79% |
| Benjamin Poirier | 62 | 2.50% | 3 | 5.17% |
| Alexander Duyck | 26 | 1.05% | 1 | 1.72% |
| Jesse Brandeburg | 18 | 0.72% | 2 | 3.45% |
| Dave Ertman | 18 | 0.72% | 3 | 5.17% |
| Christopher S. Hall | 16 | 0.64% | 1 | 1.72% |
| Dave Graham | 14 | 0.56% | 3 | 5.17% |
| Ben Greear | 5 | 0.20% | 1 | 1.72% |
| Vitaly Lifshits | 5 | 0.20% | 1 | 1.72% |
| Mitch A Williams | 5 | 0.20% | 1 | 1.72% |
| Bill Hayes | 4 | 0.16% | 1 | 1.72% |
| Jeff Kirsher | 2 | 0.08% | 2 | 3.45% |
| Total | 2483 | 58 |
/* SPDX-License-Identifier: GPL-2.0 */ /* Copyright(c) 1999 - 2018 Intel Corporation. */ #ifndef _E1000_DEFINES_H_ #define _E1000_DEFINES_H_ /* Number of Transmit and Receive Descriptors must be a multiple of 8 */ #define REQ_TX_DESCRIPTOR_MULTIPLE 8 #define REQ_RX_DESCRIPTOR_MULTIPLE 8 /* Definitions for power management and wakeup registers */ /* Wake Up Control */ #define E1000_WUC_APME 0x00000001 /* APM Enable */ #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ #define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ #define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ #define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */ /* Wake Up Filter Control */ #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ #define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ /* Wake Up Status */ #define E1000_WUS_LNKC E1000_WUFC_LNKC #define E1000_WUS_MAG E1000_WUFC_MAG #define E1000_WUS_EX E1000_WUFC_EX #define E1000_WUS_MC E1000_WUFC_MC #define E1000_WUS_BC E1000_WUFC_BC /* Extended Device Control */ #define E1000_CTRL_EXT_LPCD 0x00000004 /* LCD Power Cycle Done */ #define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */ #define E1000_CTRL_EXT_FORCE_SMBUS 0x00000800 /* Force SMBus mode */ #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ #define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ #define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */ #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000 #define E1000_CTRL_EXT_EIAME 0x01000000 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ #define E1000_CTRL_EXT_IAME 0x08000000 /* Int ACK Auto-mask */ #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */ #define E1000_CTRL_EXT_LSECCK 0x00001000 #define E1000_CTRL_EXT_PHYPDEN 0x00100000 /* Receive Descriptor bit definitions */ #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ #define E1000_RXD_ERR_CE 0x01 /* CRC Error */ #define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ #define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ #define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ #define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ #define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ #define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ #define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ #define E1000_RXDEXT_STATERR_TST 0x00000100 /* Time Stamp taken */ #define E1000_RXDEXT_STATERR_CE 0x01000000 #define E1000_RXDEXT_STATERR_SE 0x02000000 #define E1000_RXDEXT_STATERR_SEQ 0x04000000 #define E1000_RXDEXT_STATERR_CXE 0x10000000 #define E1000_RXDEXT_STATERR_RXE 0x80000000 /* mask to determine if packets should be dropped due to frame errors */ #define E1000_RXD_ERR_FRAME_ERR_MASK ( \ E1000_RXD_ERR_CE | \ E1000_RXD_ERR_SE | \ E1000_RXD_ERR_SEQ | \ E1000_RXD_ERR_CXE | \ E1000_RXD_ERR_RXE) /* Same mask, but for extended and packet split descriptors */ #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ E1000_RXDEXT_STATERR_CE | \ E1000_RXDEXT_STATERR_SE | \ E1000_RXDEXT_STATERR_SEQ | \ E1000_RXDEXT_STATERR_CXE | \ E1000_RXDEXT_STATERR_RXE) #define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000 #define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 /* Management Control */ #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ #define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ /* Enable MAC address filtering */ #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MNG packets to host memory */ #define E1000_MANC_EN_MNG2HOST 0x00200000 #define E1000_MANC2H_PORT_623 0x00000020 /* Port 0x26f */ #define E1000_MANC2H_PORT_664 0x00000040 /* Port 0x298 */ #define E1000_MDEF_PORT_623 0x00000800 /* Port 0x26f */ #define E1000_MDEF_PORT_664 0x00000400 /* Port 0x298 */ /* Receive Control */ #define E1000_RCTL_EN 0x00000002 /* enable */ #define E1000_RCTL_SBP 0x00000004 /* store bad packet */ #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ #define E1000_RCTL_LPE 0x00000020 /* long packet enable */ #define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ #define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ #define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */ #define E1000_RCTL_RDMTS_HEX 0x00010000 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ #define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */ #define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */ #define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */ #define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */ /* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ #define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */ #define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */ #define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */ #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ #define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ #define E1000_RCTL_DPF 0x00400000 /* Discard Pause Frames */ #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ #define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ /* Use byte values for the following shift parameters * Usage: * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & * E1000_PSRCTL_BSIZE0_MASK) | * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) & * E1000_PSRCTL_BSIZE1_MASK) | * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) & * E1000_PSRCTL_BSIZE2_MASK) | * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |; * E1000_PSRCTL_BSIZE3_MASK)) * where value0 = [128..16256], default=256 * value1 = [1024..64512], default=4096 * value2 = [0..64512], default=4096 * value3 = [0..64512], default=0 */ #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ /* SWFW_SYNC Definitions */ #define E1000_SWFW_EEP_SM 0x1 #define E1000_SWFW_PHY0_SM 0x2 #define E1000_SWFW_PHY1_SM 0x4 #define E1000_SWFW_CSR_SM 0x8 /* Device Control */ #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */ #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ #define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */ #define E1000_CTRL_LANPHYPC_VALUE 0x00020000 /* SW value of LANPHYPC */ #define E1000_CTRL_MEHE 0x00080000 /* Memory Error Handling Enable */ #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ #define E1000_CTRL_ADVD3WUC 0x00100000 /* D3 WUC */ #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000 /* PHY PM enable */ #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ #define E1000_CTRL_RST 0x04000000 /* Global reset */ #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ #define E1000_PCS_LCTL_FORCE_FCTRL 0x80 #define E1000_PCS_LSTS_AN_COMPLETE 0x10000 /* Device Status */ #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ #define E1000_STATUS_FUNC_SHIFT 2 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ #define E1000_STATUS_SPEED_MASK 0x000000C0 #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ #define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */ #define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */ #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master Req status */ /* PCIm function state */ #define E1000_STATUS_PCIM_STATE 0x40000000 #define HALF_DUPLEX 1 #define FULL_DUPLEX 2 #define ADVERTISE_10_HALF 0x0001 #define ADVERTISE_10_FULL 0x0002 #define ADVERTISE_100_HALF 0x0004 #define ADVERTISE_100_FULL 0x0008 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */ #define ADVERTISE_1000_FULL 0x0020 /* 1000/H is not supported, nor spec-compliant. */ #define E1000_ALL_SPEED_DUPLEX ( \ ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \ ADVERTISE_100_FULL | ADVERTISE_1000_FULL) #define E1000_ALL_NOT_GIG ( \ ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \ ADVERTISE_100_FULL) #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL) #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL) #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF) #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX /* LED Control */ #define E1000_PHY_LED0_MODE_MASK 0x00000007 #define E1000_PHY_LED0_IVRT 0x00000008 #define E1000_PHY_LED0_MASK 0x0000001F #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F #define E1000_LEDCTL_LED0_MODE_SHIFT 0 #define E1000_LEDCTL_LED0_IVRT 0x00000040 #define E1000_LEDCTL_LED0_BLINK 0x00000080 #define E1000_LEDCTL_MODE_LINK_UP 0x2 #define E1000_LEDCTL_MODE_LED_ON 0xE #define E1000_LEDCTL_MODE_LED_OFF 0xF /* Transmit Descriptor bit definitions */ #define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ #define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ #define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ #define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ #define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ #define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ #define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ #define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ #define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ #define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ #define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ #define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ #define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */ /* Transmit Control */ #define E1000_TCTL_EN 0x00000002 /* enable Tx */ #define E1000_TCTL_PSP 0x00000008 /* pad short packets */ #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ #define E1000_TCTL_COLD 0x003ff000 /* collision distance */ #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ /* SerDes Control */ #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400 #define E1000_SCTL_ENABLE_SERDES_LOOPBACK 0x0410 /* Receive Checksum Control */ #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ #define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ /* Header split receive */ #define E1000_RFCTL_NFSW_DIS 0x00000040 #define E1000_RFCTL_NFSR_DIS 0x00000080 #define E1000_RFCTL_ACK_DIS 0x00001000 #define E1000_RFCTL_EXTEN 0x00008000 #define E1000_RFCTL_IPV6_EX_DIS 0x00010000 #define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 /* Collision related configuration parameters */ #define E1000_COLLISION_THRESHOLD 15 #define E1000_CT_SHIFT 4 #define E1000_COLLISION_DISTANCE 63 #define E1000_COLD_SHIFT 12 /* Default values for the transmit IPG register */ #define DEFAULT_82543_TIPG_IPGT_COPPER 8 #define E1000_TIPG_IPGT_MASK 0x000003FF #define DEFAULT_82543_TIPG_IPGR1 8 #define E1000_TIPG_IPGR1_SHIFT 10 #define DEFAULT_82543_TIPG_IPGR2 6 #define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 #define E1000_TIPG_IPGR2_SHIFT 20 #define MAX_JUMBO_FRAME_SIZE 0x3F00 #define E1000_TX_PTR_GAP 0x1F /* Extended Configuration Control and Size */ #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020 #define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001 #define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008 #define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 #define E1000_EXTCNF_CTRL_GATE_PHY_CFG 0x00000080 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16 #define E1000_PHY_CTRL_D0A_LPLU 0x00000002 #define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004 #define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008 #define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 #define E1000_KABGTXD_BGSQLBIAS 0x00050000 /* Low Power IDLE Control */ #define E1000_LPIC_LPIET_SHIFT 24 /* Low Power Idle Entry Time */ /* PBA constants */ #define E1000_PBA_8K 0x0008 /* 8KB */ #define E1000_PBA_16K 0x0010 /* 16KB */ #define E1000_PBA_RXA_MASK 0xFFFF #define E1000_PBS_16K E1000_PBA_16K /* Uncorrectable/correctable ECC Error counts and enable bits */ #define E1000_PBECCSTS_CORR_ERR_CNT_MASK 0x000000FF #define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK 0x0000FF00 #define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT 8 #define E1000_PBECCSTS_ECC_ENABLE 0x00010000 #define IFS_MAX 80 #define IFS_MIN 40 #define IFS_RATIO 4 #define IFS_STEP 10 #define MIN_NUM_XMITS 1000 /* SW Semaphore Register */ #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ #define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ #define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */ /* Interrupt Cause Read */ #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ #define E1000_ICR_LSC 0x00000004 /* Link Status Change */ #define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */ #define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */ #define E1000_ICR_RXO 0x00000040 /* Receiver Overrun */ #define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */ #define E1000_ICR_MDAC 0x00000200 /* MDIO Access Complete */ #define E1000_ICR_SRPD 0x00010000 /* Small Receive Packet Detected */ #define E1000_ICR_ACK 0x00020000 /* Receive ACK Frame Detected */ #define E1000_ICR_MNG 0x00040000 /* Manageability Event Detected */ #define E1000_ICR_ECCER 0x00400000 /* Uncorrectable ECC Error */ /* If this bit asserted, the driver should claim the interrupt */ #define E1000_ICR_INT_ASSERTED 0x80000000 #define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */ #define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */ #define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */ #define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */ #define E1000_ICR_OTHER 0x01000000 /* Other Interrupt */ /* PBA ECC Register */ #define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */ #define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */ #define E1000_PBA_ECC_CORR_EN 0x00000001 /* ECC correction enable */ #define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */ #define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */ /* This defines the bits that are set in the Interrupt Mask * Set/Read Register. Each bit is documented below: * o RXT0 = Receiver Timer Interrupt (ring 0) * o TXDW = Transmit Descriptor Written Back * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) * o RXSEQ = Receive Sequence Error * o LSC = Link Status Change */ #define IMS_ENABLE_MASK ( \ E1000_IMS_RXT0 | \ E1000_IMS_TXDW | \ E1000_IMS_RXDMT0 | \ E1000_IMS_RXSEQ | \ E1000_IMS_LSC) /* These are all of the events related to the OTHER interrupt. */ #define IMS_OTHER_MASK ( \ E1000_IMS_LSC | \ E1000_IMS_RXO | \ E1000_IMS_MDAC | \ E1000_IMS_SRPD | \ E1000_IMS_ACK | \ E1000_IMS_MNG) /* Interrupt Mask Set */ #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ #define E1000_IMS_RXO E1000_ICR_RXO /* Receiver Overrun */ #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */ #define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO Access Complete */ #define E1000_IMS_SRPD E1000_ICR_SRPD /* Small Receive Packet */ #define E1000_IMS_ACK E1000_ICR_ACK /* Receive ACK Frame Detected */ #define E1000_IMS_MNG E1000_ICR_MNG /* Manageability Event */ #define E1000_IMS_ECCER E1000_ICR_ECCER /* Uncorrectable ECC Error */ #define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */ #define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */ #define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */ #define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */ #define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupt */ /* Interrupt Cause Set */ #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ #define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ #define E1000_ICS_OTHER E1000_ICR_OTHER /* Other Interrupt */ /* Transmit Descriptor Control */ #define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ #define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ #define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ #define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ #define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ #define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */ /* Enable the counting of desc. still to be processed. */ #define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Flow Control Constants */ #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 #define FLOW_CONTROL_TYPE 0x8808 /* 802.1q VLAN Packet Size */ #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ /* Receive Address * Number of high/low register pairs in the RAR. The RAR (Receive Address * Registers) holds the directed and multicast addresses that we monitor. * Technically, we have 16 spots. However, we reserve one of these spots * (RAR[15]) for our directed address used by controllers with * manageability enabled, allowing us room for 15 multicast addresses. */ #define E1000_RAR_ENTRIES 15 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ #define E1000_RAL_MAC_ADDR_LEN 4 #define E1000_RAH_MAC_ADDR_LEN 2 /* Error Codes */ #define E1000_ERR_NVM 1 #define E1000_ERR_PHY 2 #define E1000_ERR_CONFIG 3 #define E1000_ERR_PARAM 4 #define E1000_ERR_MAC_INIT 5 #define E1000_ERR_PHY_TYPE 6 #define E1000_ERR_RESET 9 #define E1000_ERR_MASTER_REQUESTS_PENDING 10 #define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 #define E1000_ERR_SWFW_SYNC 13 #define E1000_NOT_IMPLEMENTED 14 #define E1000_ERR_INVALID_ARGUMENT 16 #define E1000_ERR_NO_SPACE 17 #define E1000_ERR_NVM_PBA_SECTION 18 /* Loop limit on how long we wait for auto-negotiation to complete */ #define FIBER_LINK_UP_LIMIT 50 #define COPPER_LINK_UP_LIMIT 10 #define PHY_AUTO_NEG_LIMIT 45 #define PHY_FORCE_LIMIT 20 /* Number of 100 microseconds we wait for PCI Express master disable */ #define MASTER_DISABLE_TIMEOUT 800 /* Number of milliseconds we wait for PHY configuration done after MAC reset */ #define PHY_CFG_TIMEOUT 100 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */ #define MDIO_OWNERSHIP_TIMEOUT 10 /* Number of milliseconds for NVM auto read done after MAC reset. */ #define AUTO_READ_DONE_TIMEOUT 10 /* Flow Control */ #define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ #define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ /* Transmit Configuration Word */ #define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ #define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ #define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ #define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ #define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ /* Receive Configuration Word */ #define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ #define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ #define E1000_RXCW_C 0x20000000 /* Receive config */ #define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ /* HH Time Sync */ #define E1000_TSYNCTXCTL_MAX_ALLOWED_DLY_MASK 0x0000F000 /* max delay */ #define E1000_TSYNCTXCTL_SYNC_COMP 0x40000000 /* sync complete */ #define E1000_TSYNCTXCTL_START_SYNC 0x80000000 /* initiate sync */ #define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */ #define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */ #define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */ #define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */ #define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00 #define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02 #define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04 #define E1000_TSYNCRXCTL_TYPE_ALL 0x08 #define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A #define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable Rx timestamping */ #define E1000_TSYNCRXCTL_SYSCFI 0x00000020 /* Sys clock frequency */ #define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE 0x00000000 #define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE 0x00010000 #define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE 0x00000000 #define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE 0x01000000 #define E1000_TIMINCA_INCPERIOD_SHIFT 24 #define E1000_TIMINCA_INCVALUE_MASK 0x00FFFFFF /* PCI Express Control */ #define E1000_GCR_RXD_NO_SNOOP 0x00000001 #define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 #define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 #define E1000_GCR_TXD_NO_SNOOP 0x00000008 #define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 #define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 #define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ E1000_GCR_RXDSCW_NO_SNOOP | \ E1000_GCR_RXDSCR_NO_SNOOP | \ E1000_GCR_TXD_NO_SNOOP | \ E1000_GCR_TXDSCW_NO_SNOOP | \ E1000_GCR_TXDSCR_NO_SNOOP) /* NVM Control */ #define E1000_EECD_SK 0x00000001 /* NVM Clock */ #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */ #define E1000_EECD_DI 0x00000004 /* NVM Data In */ #define E1000_EECD_DO 0x00000008 /* NVM Data Out */ #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */ #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */ #define E1000_EECD_PRES 0x00000100 /* NVM Present */ #define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */ /* NVM Addressing bits based on type (0-small, 1-large) */ #define E1000_EECD_ADDR_BITS 0x00000400 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */ #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */ #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */ #define E1000_EECD_SIZE_EX_SHIFT 11 #define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ #define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ #define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ #define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES) #define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM r/w regs */ #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ #define E1000_NVM_RW_REG_START 1 /* Start operation */ #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ #define E1000_NVM_POLL_WRITE 1 /* Flag for polling write complete */ #define E1000_NVM_POLL_READ 0 /* Flag for polling read complete */ #define E1000_FLASH_UPDATES 2000 /* NVM Word Offsets */ #define NVM_COMPAT 0x0003 #define NVM_ID_LED_SETTINGS 0x0004 #define NVM_FUTURE_INIT_WORD1 0x0019 #define NVM_COMPAT_VALID_CSUM 0x0001 #define NVM_FUTURE_INIT_WORD1_VALID_CSUM 0x0040 #define NVM_INIT_CONTROL2_REG 0x000F #define NVM_INIT_CONTROL3_PORT_B 0x0014 #define NVM_INIT_3GIO_3 0x001A #define NVM_INIT_CONTROL3_PORT_A 0x0024 #define NVM_CFG 0x0012 #define NVM_ALT_MAC_ADDR_PTR 0x0037 #define NVM_CHECKSUM_REG 0x003F #define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */ #define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */ /* Mask bits for fields in Word 0x0f of the NVM */ #define NVM_WORD0F_PAUSE_MASK 0x3000 #define NVM_WORD0F_PAUSE 0x1000 #define NVM_WORD0F_ASM_DIR 0x2000 /* Mask bits for fields in Word 0x1a of the NVM */ #define NVM_WORD1A_ASPM_MASK 0x000C /* Mask bits for fields in Word 0x03 of the EEPROM */ #define NVM_COMPAT_LOM 0x0800 /* length of string needed to store PBA number */ #define E1000_PBANUM_LENGTH 11 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */ #define NVM_SUM 0xBABA /* PBA (printed board assembly) number words */ #define NVM_PBA_OFFSET_0 8 #define NVM_PBA_OFFSET_1 9 #define NVM_PBA_PTR_GUARD 0xFAFA #define NVM_WORD_SIZE_BASE_SHIFT 6 /* NVM Commands - SPI */ #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ #define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */ #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */ #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */ #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */ /* SPI NVM Status Register */ #define NVM_STATUS_RDY_SPI 0x01 /* Word definitions for ID LED Settings */ #define ID_LED_RESERVED_0000 0x0000 #define ID_LED_RESERVED_FFFF 0xFFFF #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ (ID_LED_OFF1_OFF2 << 8) | \ (ID_LED_DEF1_DEF2 << 4) | \ (ID_LED_DEF1_DEF2)) #define ID_LED_DEF1_DEF2 0x1 #define ID_LED_DEF1_ON2 0x2 #define ID_LED_DEF1_OFF2 0x3 #define ID_LED_ON1_DEF2 0x4 #define ID_LED_ON1_ON2 0x5 #define ID_LED_ON1_OFF2 0x6 #define ID_LED_OFF1_DEF2 0x7 #define ID_LED_OFF1_ON2 0x8 #define ID_LED_OFF1_OFF2 0x9 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF #define IGP_ACTIVITY_LED_ENABLE 0x0300 #define IGP_LED3_MODE 0x07000000 /* PCI/PCI-X/PCI-EX Config space */ #define PCI_HEADER_TYPE_REGISTER 0x0E #define PCIE_LINK_STATUS 0x12 #define PCI_HEADER_TYPE_MULTIFUNC 0x80 #define PCIE_LINK_WIDTH_MASK 0x3F0 #define PCIE_LINK_WIDTH_SHIFT 4 #define PHY_REVISION_MASK 0xFFFFFFF0 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ #define MAX_PHY_MULTI_PAGE_REG 0xF /* Bit definitions for valid PHY IDs. * I = Integrated * E = External */ #define M88E1000_E_PHY_ID 0x01410C50 #define M88E1000_I_PHY_ID 0x01410C30 #define M88E1011_I_PHY_ID 0x01410C20 #define IGP01E1000_I_PHY_ID 0x02A80380 #define M88E1111_I_PHY_ID 0x01410CC0 #define GG82563_E_PHY_ID 0x01410CA0 #define IGP03E1000_E_PHY_ID 0x02A80390 #define IFE_E_PHY_ID 0x02A80330 #define IFE_PLUS_E_PHY_ID 0x02A80320 #define IFE_C_E_PHY_ID 0x02A80310 #define BME1000_E_PHY_ID 0x01410CB0 #define BME1000_E_PHY_ID_R2 0x01410CB1 #define I82577_E_PHY_ID 0x01540050 #define I82578_E_PHY_ID 0x004DD040 #define I82579_E_PHY_ID 0x01540090 #define I217_E_PHY_ID 0x015400A0 /* M88E1000 Specific Registers */ #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ /* M88E1000 PHY Specific Control Register */ #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ /* Manual MDI configuration */ #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */ #define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* Auto crossover enabled all speeds */ #define M88E1000_PSCR_AUTO_X_MODE 0x0060 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ /* M88E1000 PHY Specific Status Register */ #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ /* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */ #define M88E1000_PSSR_CABLE_LENGTH 0x0380 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 /* Number of times we will attempt to autonegotiate before downshifting if we * are the master */ #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 /* Number of times we will attempt to autonegotiate before downshifting if we * are the slave */ #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ /* M88EC018 Rev 2 specific DownShift settings */ #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 #define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020 #define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C /* BME1000 PHY Specific Control Register */ #define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */ /* Bits... * 15-5: page * 4-0: register offset */ #define GG82563_PAGE_SHIFT 5 #define GG82563_REG(page, reg) \ (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) #define GG82563_MIN_ALT_REG 30 /* GG82563 Specific Registers */ #define GG82563_PHY_SPEC_CTRL \ GG82563_REG(0, 16) /* PHY Specific Control */ #define GG82563_PHY_PAGE_SELECT \ GG82563_REG(0, 22) /* Page Select */ #define GG82563_PHY_SPEC_CTRL_2 \ GG82563_REG(0, 26) /* PHY Specific Control 2 */ #define GG82563_PHY_PAGE_SELECT_ALT \ GG82563_REG(0, 29) /* Alternate Page Select */ #define GG82563_PHY_MAC_SPEC_CTRL \ GG82563_REG(2, 21) /* MAC Specific Control Register */ #define GG82563_PHY_DSP_DISTANCE \ GG82563_REG(5, 26) /* DSP Distance */ /* Page 193 - Port Control Registers */ #define GG82563_PHY_KMRN_MODE_CTRL \ GG82563_REG(193, 16) /* Kumeran Mode Control */ #define GG82563_PHY_PWR_MGMT_CTRL \ GG82563_REG(193, 20) /* Power Management Control */ /* Page 194 - KMRN Registers */ #define GG82563_PHY_INBAND_CTRL \ GG82563_REG(194, 18) /* Inband Control */ /* MDI Control */ #define E1000_MDIC_REG_MASK 0x001F0000 #define E1000_MDIC_REG_SHIFT 16 #define E1000_MDIC_PHY_SHIFT 21 #define E1000_MDIC_OP_WRITE 0x04000000 #define E1000_MDIC_OP_READ 0x08000000 #define E1000_MDIC_READY 0x10000000 #define E1000_MDIC_ERROR 0x40000000 /* SerDes Control */ #define E1000_GEN_POLL_TIMEOUT 640 #endif /* _E1000_DEFINES_H_ */
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1