Contributors: 16
Author Tokens Token Proportion Commits Commit Proportion
Linus Torvalds (pre-git) 246 56.55% 17 48.57%
Nicolas Ferre 43 9.89% 1 2.86%
Ilpo Järvinen 37 8.51% 1 2.86%
Alan Cox 26 5.98% 2 5.71%
Russell King 21 4.83% 2 5.71%
Peter Hurley 16 3.68% 1 2.86%
Crescent CY Hsieh 10 2.30% 2 5.71%
David Howells 9 2.07% 1 2.86%
Christoph Niedermaier 7 1.61% 1 2.86%
Masahiro Yamada 4 0.92% 1 2.86%
David Woodhouse 4 0.92% 1 2.86%
Claudio Scordino 4 0.92% 1 2.86%
Jan Kiszka 3 0.69% 1 2.86%
Bernhard Roth 3 0.69% 1 2.86%
Greg Kroah-Hartman 1 0.23% 1 2.86%
Philippe Langlais 1 0.23% 1 2.86%
Total 435 35 


/* SPDX-License-Identifier: GPL-1.0+ WITH Linux-syscall-note */
/*
 * include/linux/serial.h
 *
 * Copyright (C) 1992 by Theodore Ts'o.
 * 
 * Redistribution of this file is permitted under the terms of the GNU 
 * Public License (GPL)
 */

#ifndef _UAPI_LINUX_SERIAL_H
#define _UAPI_LINUX_SERIAL_H

#include <linux/const.h>
#include <linux/types.h>

#include <linux/tty_flags.h>


struct serial_struct {
	int	type;
	int	line;
	unsigned int	port;
	int	irq;
	int	flags;
	int	xmit_fifo_size;
	int	custom_divisor;
	int	baud_base;
	unsigned short	close_delay;
	char	io_type;
	char	reserved_char[1];
	int	hub6;
	unsigned short	closing_wait; /* time to wait before closing */
	unsigned short	closing_wait2; /* no longer used... */
	unsigned char	*iomem_base;
	unsigned short	iomem_reg_shift;
	unsigned int	port_high;
	unsigned long	iomap_base;	/* cookie passed into ioremap */
};

/*
 * For the close wait times, 0 means wait forever for serial port to
 * flush its output.  65535 means don't wait at all.
 */
#define ASYNC_CLOSING_WAIT_INF	0
#define ASYNC_CLOSING_WAIT_NONE	65535

/*
 * These are the supported serial types.
 */
#define PORT_UNKNOWN	0
#define PORT_8250	1
#define PORT_16450	2
#define PORT_16550	3
#define PORT_16550A	4
#define PORT_CIRRUS     5
#define PORT_16650	6
#define PORT_16650V2	7
#define PORT_16750	8
#define PORT_STARTECH	9
#define PORT_16C950	10	/* Oxford Semiconductor */
#define PORT_16654	11
#define PORT_16850	12
#define PORT_RSA	13	/* RSA-DV II/S card */
#define PORT_MAX	13

#define SERIAL_IO_PORT	0
#define SERIAL_IO_HUB6	1
#define SERIAL_IO_MEM	2
#define SERIAL_IO_MEM32	  3
#define SERIAL_IO_AU	  4
#define SERIAL_IO_TSI	  5
#define SERIAL_IO_MEM32BE 6
#define SERIAL_IO_MEM16	7

#define UART_CLEAR_FIFO		0x01
#define UART_USE_FIFO		0x02
#define UART_STARTECH		0x04
#define UART_NATSEMI		0x08


/*
 * Multiport serial configuration structure --- external structure
 */
struct serial_multiport_struct {
	int		irq;
	int		port1;
	unsigned char	mask1, match1;
	int		port2;
	unsigned char	mask2, match2;
	int		port3;
	unsigned char	mask3, match3;
	int		port4;
	unsigned char	mask4, match4;
	int		port_monitor;
	int	reserved[32];
};

/*
 * Serial input interrupt line counters -- external structure
 * Four lines can interrupt: CTS, DSR, RI, DCD
 */
struct serial_icounter_struct {
	int cts, dsr, rng, dcd;
	int rx, tx;
	int frame, overrun, parity, brk;
	int buf_overrun;
	int reserved[9];
};

/**
 * struct serial_rs485 - serial interface for controlling RS485 settings.
 * @flags:			RS485 feature flags.
 * @delay_rts_before_send:	Delay before send (milliseconds).
 * @delay_rts_after_send:	Delay after send (milliseconds).
 * @addr_recv:			Receive filter for RS485 addressing mode
 *				(used only when %SER_RS485_ADDR_RECV is set).
 * @addr_dest:			Destination address for RS485 addressing mode
 *				(used only when %SER_RS485_ADDR_DEST is set).
 * @padding0:			Padding (set to zero).
 * @padding1:			Padding (set to zero).
 * @padding:			Deprecated, use @padding0 and @padding1 instead.
 *				Do not use with @addr_recv and @addr_dest (due to
 *				overlap).
 *
 * Serial interface for controlling RS485 settings on chips with suitable
 * support. Set with TIOCSRS485 and get with TIOCGRS485 if supported by your
 * platform. The set function returns the new state, with any unsupported bits
 * reverted appropriately.
 *
 * The flag bits are:
 *
 * * %SER_RS485_ENABLED		- RS485 enabled.
 * * %SER_RS485_RTS_ON_SEND	- Logical level for RTS pin when sending.
 * * %SER_RS485_RTS_AFTER_SEND	- Logical level for RTS pin after sent.
 * * %SER_RS485_RX_DURING_TX	- Full-duplex RS485 line.
 * * %SER_RS485_TERMINATE_BUS	- Enable bus termination (if supported).
 * * %SER_RS485_ADDRB		- Enable RS485 addressing mode.
 * * %SER_RS485_ADDR_RECV - Receive address filter (enables @addr_recv). Requires %SER_RS485_ADDRB.
 * * %SER_RS485_ADDR_DEST - Destination address (enables @addr_dest). Requires %SER_RS485_ADDRB.
 * * %SER_RS485_MODE_RS422	- Enable RS422. Requires %SER_RS485_ENABLED.
 */
struct serial_rs485 {
	__u32	flags;
#define SER_RS485_ENABLED		_BITUL(0)
#define SER_RS485_RTS_ON_SEND		_BITUL(1)
#define SER_RS485_RTS_AFTER_SEND	_BITUL(2)
/* Placeholder for bit 3: SER_RS485_RTS_BEFORE_SEND, which isn't used anymore */
#define SER_RS485_RX_DURING_TX		_BITUL(4)
#define SER_RS485_TERMINATE_BUS		_BITUL(5)
#define SER_RS485_ADDRB			_BITUL(6)
#define SER_RS485_ADDR_RECV		_BITUL(7)
#define SER_RS485_ADDR_DEST		_BITUL(8)
#define SER_RS485_MODE_RS422		_BITUL(9)

	__u32	delay_rts_before_send;
	__u32	delay_rts_after_send;

	/* The fields below are defined by flags */
	union {
		__u32	padding[5];		/* Memory is cheap, new structs are a pain */

		struct {
			__u8	addr_recv;
			__u8	addr_dest;
			__u8	padding0[2];
			__u32	padding1[4];
		};
	};
};

/*
 * Serial interface for controlling ISO7816 settings on chips with suitable
 * support. Set with TIOCSISO7816 and get with TIOCGISO7816 if supported by
 * your platform.
 */
struct serial_iso7816 {
	__u32	flags;			/* ISO7816 feature flags */
#define SER_ISO7816_ENABLED		(1 << 0)
#define SER_ISO7816_T_PARAM		(0x0f << 4)
#define SER_ISO7816_T(t)		(((t) & 0x0f) << 4)
	__u32	tg;
	__u32	sc_fi;
	__u32	sc_di;
	__u32	clk;
	__u32	reserved[5];
};

#endif /* _UAPI_LINUX_SERIAL_H */